Zgemma HS2 - Stuck on Boot - No Channels - PLEASE HELP

[Ferret]

how you sloved my STb also stuck on boot
logo

He simply reflashed it.

 

[truefrnd]

He simply reflashed it.

i have reflash and tried many image but same status, stuk on boot logo

 

[Ferret]

i have reflash and tried many image but same status, stuk on boot logo

Do you actually see it flash sometimes USB sticks are not read.

If you sure it flashed try another PSU this can cause it to stick on boot if its weak.

 

[JohnKilkenny]

Ok so if it runs a openbox its probably a Universal LNB.

So how have you got you tuner setup

If your dish is looking at 28e

Simple
Single
28e

Should do the trick make sure the lnb cable is going to the tuner you have configured.

Hi

will give it another go tomorrow to see if i can get it up and running

 

[truefrnd]

Do you actually see it flash sometimes USB sticks are not read.

If you sure it flashed try another PSU this can cause it to stick on boot if its weak.

its flashed complete 100%. no usb error. after successfull flash it always stuk on boot

 

[Ferret]

its flashed complete 100%. no usb error. after successfull flash it always stuk on boot

Have you tried another power supply then ?

 

[truefrnd]

Have you tried another power supply then ?

not tried

 

[Ferret]

not tried

Well do so i think this will fix it, as the box tries to boot and bring in the tuner etc more demand is put on the power supply when power supplies start to go weak the box fail to bring in the tuner etc and wont boot.

 

[JohnKilkenny]

Hi can anybody help i have a Zgemma h2s stuck on boot have tried to flash but the box doesn’t pick up the image

Hi have flashed my Zgemma h2s get as far as signal finder but have no signal strength and can’t lock to the 28.2e for some reason anybody have any ides

 

[Ferret]

Hi have flashed my Zgemma h2s get as far as signal finder but have no signal strength and can’t lock to the 28.2e for some reason anybody have any ides

How do you have your tuner setup ?

 

[Abu Baniaz]

Do you have signal wires attached to both tuners? If not, the ones without signal wire should be set as not configured/disabled. Ferret has posted what the tuner/s for 28.2 should be set as. He has asked for confirmation of what you have done

I would not have gone into signal finder, i would have just performed a manual scan, single satellite, 28.2. You should get over 800 channels. In signal finder, you have to select a transponder to check. Maybe you were checking a transponder you can't receive.

The other possibility is a hardware fault. Some LNBs will have issues when more than one receiver is powering it. You can try and power down the two openboxes, not just standby. Or try connecting the zgemma to the signal wire that you know is working on the openbox.

 

[JohnKilkenny]

Hi I have done all this over the weekend except disconnect both openboxes but still when I do a manual scan and still the scan comes back with no channels found????

 

[Ferret]

Hi I have done all this over the weekend except disconnect both openboxes but still when I do a manual scan and still the scan comes back with no channels found????

I asked you how you have your tuner setup and you didnt reply.

 

[JohnKilkenny]

Sorry I didn't see this response I'm not sure how the tuner is setup & where do I look to find out this information

 

[Ferret]

Sorry I didn't see this response I'm not sure how the tuner is setup & where do I look to find out this information

Menu-setup-reception

You need it setup like this

Single
Simple
28e

 

[JohnKilkenny]

Thank you will give it a go later 7 let you know how I get on