You have to activate the new card in no case with SCAM, CCcam or similar Cam as these all EMM's be transmitted and thus the risk that the card is paired. What EMM's should be blocked
It is advisable would be a ECMWhitelist to work on servers attempt to eventual pairing through a manipulated ECM to counteract this one must of course always keep current with changes
Configuration of a receiver with only OScam
here the dvbapi section should be set up correctly in the oscam.conf
in oscam.server all EMM's should be blocked until the Unique, through this most likely comes pairing EMM, but we can through the Parameter Filter blockemm_bylen using the Sammelthreads what lengths we transmit
in oscam.user the local account should the right to have to supply the card with updates
oscam.conf
[Dvbapi]
enabled = 1
au = 1
user = locally
BoxType = dreambox
oscam.user
[Account]
user = locally
au = V14
group = 1
oscam.server
(This one should pay attention to the cardmhz / mhz, with newer OScam versions and use the internal card reader you should modify the parameters so between 8940 and 9098 they have to look like this: mhz = 2700 cardmhz = -1 and from 9099 it should look like this: mhz = 1 cardmhz = 2700
[Reader]
label = V14
protocol = internal
device = / dev / SCI0
auto speed = 0
caid = 098C
BoxID = 12345678
ins7e11 = 15
detect = cd
group = 1
ecmwhitelist = 098C: 98,9B, 97,57,91
emmcache = 1,1,2
blockemm-unknown = 1
blockemm-s = 1
blockemm-g = 1
blockemm-Bylen = 1-31,36,38,40-41,65-72,74-124,126,128-129,131,141-255
ndsversion = 2
oscam.dvbapi (here we prioritize the caid of the V14, with the "1" behind only this is requested and with the entry "I 0" is at the end ignores everything else)
P: 098C 1
I: 0
The same should be done with a V13, this only Caid 098C change against the 09C4
Configuring a Server and Clients OScam
server
the server is somewhat similar set up as described above
oscam.conf
[Cccam]
port = 12000
version = 2.3.0
reshare = 1
oscam.user
[Account]
user =
pwd = zumUPDATEN
au = V14
group = 1
oscam.server
(This should be the entry "mhz" be the same as the adjusted clock to your card reader)
[Reader]
label = V14
protocol = mouse
device = / dev / ttyUSB0
mhz = 357
auto speed = 0
cardmhz = 357
caid = 098C
BoxID = 12345678
ins7e11 = 15
detect = cd
group = 1
ecmwhitelist = 098C: 98,9B, 97,57,91
emmcache = 1,1,2
blockemm-unknown = 1
blockemm-s = 1
blockemm-g = 1
blockemm-Bylen = 1-31,36,38,40-41,65-72,74-124,126,128-129,131,141-255
ndsversion = 2
client
the client with OScam about Cccam protocol is established as follows
Example Dreambox:
[Dvbapi]
enabled = 1
au = 1
user = locally
BoxType = dreambox
oscam.user
[Account]
user = locally
au = Server
group = 1
oscam.server
[Reader]
label = Server
protocol = cccam
device = IPdesSERVERS, 12000
user =
password = zumUPDATEN
group = 1
cccversion = 2.3.0
ccckeepalive = 1
oscam.dvbapi
(Here we prioritize the caid of the V14, with the "1" behind only this is requested and with the entry "I 0" is at the end ignores everything else)
P: 098C 1
I: 0
Of course we could also in the reader all EMM's Block and then hand the card writing, is just a bit more expensive but would not say that it is safer
Now we should be send from the Customer an enable signal and hope that we at least little joy of have V14