Welcome to our community
Be apart of something great, join today!
Broken Liteon drive
- Thread starter Mepsipax
- Start date
Ok here is one of them. I have changed the last 4 digits of the Liteon dummy file to X's for safety.
JungleFlasher 0.1.66 Beta
Session Started Sat Oct 17 13:07:59 2009
This is a 32 bit process running on 2 x 32 bit CPUs
PortIO is installed and running.
Found 4 I/O Ports.
Found 1 Com Ports.
Found 5 windows drives A: C: D: E: F:
Found 0 CD/DVD drives
Loading Source File C:\Xbox360\Dummy.bin
Inquiry string found
Identify string found
DVD key found @ 0xA030 key is DFA38C1315B53C90214F28E05F32XXXX
Firmware is a Lite-On Dummy OSIG:
Firmware type is: LO83info Extract
Loading target file C:\Xbox360\JungleFlasher v0.1.66 Beta (49)\firmware\ix16-benq.bin
Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27
Genuine Benq iXtreme 1.6
Inquiry string found
Identify string found
DVD key found @ 0xE030 key is 77777777777777777777777777777777
Firmware is Benq OSIG: PBDS VAD6038-64930C
Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038
Sending Vendor Intro to port 0xE880
Serial flash found with Status 0x73
Sending Device ID request to port 0xE880
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Spoofing Target
DVD Key copied to target
Inquiry string copied from Source to Target
Inquiry string also copied to banks 1, 2, 3 for Benq
Identify string copied from Source to Target
Identify string also copied to banks 1, 2, 3 for Benq
Target spoofed as: PLDS DG-16D2S 8385
Getting Status from port 0xE880
SPi flash found with Status 0x73
Sending Chip Erase to Port 0xE880
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
Sending Vendor Outro to port 0xE880
JungleFlasher 0.1.66 Beta
Session Started Sat Oct 17 13:07:59 2009
This is a 32 bit process running on 2 x 32 bit CPUs
PortIO is installed and running.
Found 4 I/O Ports.
Found 1 Com Ports.
Found 5 windows drives A: C: D: E: F:
Found 0 CD/DVD drives
Loading Source File C:\Xbox360\Dummy.bin
Inquiry string found
Identify string found
DVD key found @ 0xA030 key is DFA38C1315B53C90214F28E05F32XXXX
Firmware is a Lite-On Dummy OSIG:
Firmware type is: LO83info Extract
Loading target file C:\Xbox360\JungleFlasher v0.1.66 Beta (49)\firmware\ix16-benq.bin
Target File MD5 hash is: f36c85c5bfba325b283417f8643d7c27
Genuine Benq iXtreme 1.6
Inquiry string found
Identify string found
DVD key found @ 0xE030 key is 77777777777777777777777777777777
Firmware is Benq OSIG: PBDS VAD6038-64930C
Firmware type is: iXtreme v1.60-12x-FINAL-VAD6038
Sending Vendor Intro to port 0xE880
Serial flash found with Status 0x73
Sending Device ID request to port 0xE880
Manufacturer ID: 0xC2
Device ID: 0x11
Flash Name: MXIC(MX25L2005)
Flash Size: 262144 bytes
Spoofing Target
DVD Key copied to target
Inquiry string copied from Source to Target
Inquiry string also copied to banks 1, 2, 3 for Benq
Identify string copied from Source to Target
Identify string also copied to banks 1, 2, 3 for Benq
Target spoofed as: PLDS DG-16D2S 8385
Getting Status from port 0xE880
SPi flash found with Status 0x73
Sending Chip Erase to Port 0xE880
Writing target buffer to flash
Writing Bank 0: ................
Writing Bank 1: ................
Writing Bank 2: ................
Writing Bank 3: ................
Flash Verification Test !
Reading Bank 0: ................
Reading Bank 1: ................
Reading Bank 2: ................
Reading Bank 3: ................
Write verified OK !
Sending Vendor Outro to port 0xE880
Quote:
Nonsense... replace the sata cable just and with the key on a new drive you should be fine
if the key is correct and the drive ok then he probably does need a new motherboard unless some one here can repair it at component level . when the pins bent it has probably shorted something out .
even with a blank drive key it wouldnt keep ejecting the drive
Nonsense... replace the sata cable just and with the key on a new drive you should be fine
if the key is correct and the drive ok then he probably does need a new motherboard unless some one here can repair it at component level . when the pins bent it has probably shorted something out .
even with a blank drive key it wouldnt keep ejecting the drive
The drive was ejecting before the pins bent. So I don't think a short caused this problem.
(Also I did check the 360 before attempting the flash, and it was fine running
games, and no ejecting).
Has anyone here any experience with opened 360 returns to Microsoft?
I can get a new sticker, but the Liteon drive will obviously still have the
mangled pins behind the plastic sata connector.
- I would rather have fixed this, but have spent too much time, and am still completely stuck!
Hi mate at what point did it start ejecting like? just wondering that's all.
I'd be inclined to get that drive fixed and bollix it start again with the orginal drive, might of course be a waste of time and that but of course it might not like. imagine after getting it fixed it started ejecting, i know it'd be a pain in the ass.
Just seems well weird this old constant ejecting all the time.
I'd be inclined to get that drive fixed and bollix it start again with the orginal drive, might of course be a waste of time and that but of course it might not like. imagine after getting it fixed it started ejecting, i know it'd be a pain in the ass.
Just seems well weird this old constant ejecting all the time.
Hi Dibbers
The Liteon (original) drive began ejecting as soon as I had extracted its key.
When selecting Outro Mode, JungleFlasher froze, so I had to eventually switch off the xbox.
Then when I booted it up again, the drive began ejecting.
After that I spent ages trying to get JF to get the 360 out of Vendor Mode.
That is when I tried pulling out the hard drive cable, then the sata cable, to see if it helped. It didn't all that it achieved was me accidentally pulling out the sata end, then I bent the pins.
Then I bought the Benq drive, and the same happened.
So as you can see, the pins thing happened some while after the ejecting problem.
As for fixing the Liteon, if it was just a straightforward fix I would attempt it but I guess it will need soldering?
Thing is, I still think it maybe just a flashing error - possibly due to it being one of the new batch Liteons?
Anyway, I will take another look after work later - can't wait!!
The Liteon (original) drive began ejecting as soon as I had extracted its key.
When selecting Outro Mode, JungleFlasher froze, so I had to eventually switch off the xbox.
Then when I booted it up again, the drive began ejecting.
After that I spent ages trying to get JF to get the 360 out of Vendor Mode.
That is when I tried pulling out the hard drive cable, then the sata cable, to see if it helped. It didn't all that it achieved was me accidentally pulling out the sata end, then I bent the pins.
Then I bought the Benq drive, and the same happened.
So as you can see, the pins thing happened some while after the ejecting problem.
As for fixing the Liteon, if it was just a straightforward fix I would attempt it but I guess it will need soldering?
Thing is, I still think it maybe just a flashing error - possibly due to it being one of the new batch Liteons?
Anyway, I will take another look after work later - can't wait!!
yeah could well be one of the new one's - after extracting key making it constantly eject and same with a spare drive is well weird. i guess it's all in experimental stages the new ones....as per JF does say you can't flash them new ones like.....you may be among the 1st people to experience problems with what happens if you do try and flash the new ones.....hope not like, it would be nice to see it fixed.
