gopher2005
Inactive User
hi iv got an ambit 100 gone through tut got to the stage
where i have to use hyperterminal to boot modem but it wont stop boot when i press any key after 2secs? so i cant acsess the menu? my rs232 interface is conected fine to my com1 port? any sugestions? plus i tryed terra but that just loads crap on the screen? this is what terminal loads
þ134ce7865
Boot Code SW Version 3.11.3
BCM3345 Ambit
S12ce7865Detect MXIC MX219LV160B Flash
Ambit Cable Modem Console Management
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is 000:59:E9:E3:90
This board's USB Interface hardware address is 000:59:E9:E3:91
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.101]
The file to download and start is ntlhm120_ntl0001.cpr
--------------------------------------------------------------------------
Detect MXIC MX219LV160B Flash
Running image1 !!!!!
BCM3345 Image
S12ce7865 ##ECS Magic number was wrong. Working with default value.
Detect MXIC MX219LV160B Flash
<USB ni init>
Location of Root is 80105ae0
Running from RAM
Detect MXIC MX219LV160B Flash
This is image1
Detect a filesystem
Boot loader updated....
DNS service enable
DHCP Server init (Use Default)
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue software reset
Waiting for reset finished
Init EMAC registers
Send encryption key requInit Mibs
ests
USBD started
UsUSB NDIS Driver
Reading programmed USB Configuration...
e USB init OK
DHCP
VoIP card interface is NOT enabled.
The tuner is a Temic 4937_8769
The upstream amplifier is a MicroTune 1530
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
any sugestions?thanks
where i have to use hyperterminal to boot modem but it wont stop boot when i press any key after 2secs? so i cant acsess the menu? my rs232 interface is conected fine to my com1 port? any sugestions? plus i tryed terra but that just loads crap on the screen? this is what terminal loads
þ134ce7865
Boot Code SW Version 3.11.3
BCM3345 Ambit
S12ce7865Detect MXIC MX219LV160B Flash
Ambit Cable Modem Console Management
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is 000:59:E9:E3:90
This board's USB Interface hardware address is 000:59:E9:E3:91
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.101]
The file to download and start is ntlhm120_ntl0001.cpr
--------------------------------------------------------------------------
Detect MXIC MX219LV160B Flash
Running image1 !!!!!
BCM3345 Image
S12ce7865 ##ECS Magic number was wrong. Working with default value.
Detect MXIC MX219LV160B Flash
<USB ni init>
Location of Root is 80105ae0
Running from RAM
Detect MXIC MX219LV160B Flash
This is image1
Detect a filesystem
Boot loader updated....
DNS service enable
DHCP Server init (Use Default)
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue software reset
Waiting for reset finished
Init EMAC registers
Send encryption key requInit Mibs
ests
USBD started
UsUSB NDIS Driver
Reading programmed USB Configuration...
e USB init OK
DHCP
VoIP card interface is NOT enabled.
The tuner is a Temic 4937_8769
The upstream amplifier is a MicroTune 1530
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
any sugestions?thanks