here is what i get in hyper terminal
--------------------------------------------------------------------
-- STB225 Primary Bootloader dev, NI (21:17:47, Apr 16 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 1024 cols x 8192 rows: 128 MBytes
SIF1: 1024 cols x 8192 rows: 128 MBytes
DRAM: 200 MHz, 2 x 128 MBytes: 256 MBytes
NAND: ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 172146 uSec
U-Boot 1.2.0.dev (Secondary Bootloader) (Apr 14 2010 - 03:13:41)
CPU: PNX????
Secure boot: disabled
DRAM: 256 MB
## Unknown FLASH on Bank 1 - Size = 0x00000000 = 0 MB
NOR: 0 kB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x004b0000: bad block
NAND 0x00d24000: bad block
NAND 0x03758000: bad block
NAND 0x03c58000: bad block
Using default environment
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 611 msec
Hit any key to stop autoboot: 0
Loading from 64MiB 3,3V 8-bit, offset 0x1a0000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800000 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1570274 Bytes = 1.5 MB
Load Address: 80001000
Entry Point: 802a9b40
Verifying Checksum ... Bad Data CRC
--------------------------------------------------------------------
-- STB225 Primary Bootloader dev, NI (21:17:47, Apr 16 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 1024 cols x 8192 rows: 128 MBytes
SIF1: 1024 cols x 8192 rows: 128 MBytes
DRAM: 200 MHz, 2 x 128 MBytes: 256 MBytes
NAND: ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: corrupt image
NAND 0x004B0000: bad block
NAND 0x00D24000: bad block
NAND 0x03758000: bad block
NAND 0x03C58000: bad block
NAND 0x04000000: end of device
Aborting: (no image found)
Fatal: boot failed
i cant get into mini root
ive emailed directly to see about a serial loader m8
Saying that I can access the miniroot option, but despite flashing with the new 02.06 image I still get same issue.
We use essential cookies to make this site work, and optional cookies to enhance your experience.