will technomate standard receivers supports CS 2.1.3 or higher

[viper76]

any news on getting update for our boxes to support cccam 2.1.3 or higher

 

[teknokat]

.im supprised there has not been any interest in this thread, i run technomate 5402 hd whith no choice but to use cccam 2.1.2 and i also run old technomate 9100s linux, i used to use cccam 2.1.2 on it but recently i updated to cccam 2.1.4 and i can say that the 9100s is more stable and less glitchy since my update, so yes it would be nice if technomate gave us the choise for 5402hd by for now teknokat.

 

[xxxxxx]

on TM6800-6900-7100-7102-6902-5402 standard receivers using Add-on CCcam 2.0.11, I never see a new one since magic done it Add-on for TM6800-6900-7100 if you till your server to run a test from his side he will till you at you are runing CCcam 2.0.11 m8 and I can not see that technomate Phantom are going to bring a new one out since all these years, all I can till you that from OSCam too CCcam TM6800 TM6900 TM5402 all I can say that working fine for now

 

[teknokat]

hi xxxxxx, i am using cccam 2.1.4 on 9100s linux downloaded from downloadcentre. file is tm9100s update 1115.image [8.0 mb] 15.11.2010 updated 12.11.2011 hits 107. i did not know when installing on reciever what cccam version it was going to be, all i am saying is why is it not made for other recievers,i am not going into it too deep but cccam 2.1.4 0n 9100s locks onto channels quicker and works for me better than cccam 2.1.2 on 5420hd,i am not sure of the exact cccam number for 5402hd but i am sure of the 2.1.4 for 9100s linux because it comes up whith channel info, bye for now , teknokat

 

[xxxxxx]

hi xxxxxx, i am using cccam 2.1.4 on 9100s linux downloaded from downloadcentre. file is tm9100s update 1115.image [8.0 mb] 15.11.2010 updated 12.11.2011 hits 107. i did not know when installing on reciever what cccam version it was going to be, all i am saying is why is it not made for other recievers,i am not going into it too deep but cccam 2.1.4 0n 9100s locks onto channels quicker and works for me better than cccam 2.1.2 on 5420hd,i am not sure of the exact cccam number for 5402hd but i am sure of the 2.1.4 for 9100s linux because it comes up whith channel info, bye for now , teknokat

Hi teknokat m8

TM9100s it is linux box they can take any CCcam m8, it is not LINUX TM5402

but TM6800-6900-7100 then useing Add-on dummy CCcam 2.0.11 this he done it patch maker magic he used to work for TM I never see a new one since magic can not see that technomate Phantom are going to bring a new one out since all these years and Add-on wont they are useing on TM7102-6902-5402the same one wont used old TM6800-6900-7100 and if I have agood memery this Add-on is about 3years old now

 

[stpierre]

Hi to all,

As I wrote in a previous thread :
I use VplugServer to open some channels on my Technomate 7100HD with ethernet.
VplugServer run on a PC and the Technomate use CCcam2.xxx

Since 30th juny TntSat 19°east use longer ECM.
VplugServer since v1.0.2.16 is able to support those longs ECM, but not the Technomate with the actual addon !
On some Linux receivers with Oscam release > = 5496 those longs ECM are supported and TntSat is open easily with VplugServer.

To "Phantom", is it possible to upgrade this addon ?
Thanks

For info
TntSat don't work with last patch since a few days !
Only HD channels are open