hi all i have been doing my first reset glich hack and have got to programing my cmod. I have got iXilinx ISE Design Suite 13.3 mpact running but can not seem to get it to find my cmod this is the error i get
Welcome to iMPACT
iMPACT Version: 13.3
Project: C:\Xilinx\13.3\ISE_DS\\auto_project.ipf created.
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
Enumerating cables. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Source driver files not found.
The Platform Cable USB is not detected. Please connect a cable.If a cable is connected, please disconnect
and reconnect to the usb port, follow the instructions in the 'Found New Hardware Wizard', then retry
the Cable Setup operation.
PROGRESS_END - End Operation.
Elapsed time = 2 sec.
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
// *** BATCH CMD : setCable -target "xilinx_parallel PORT=LPT1 FREQUENCY=2500000"
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
LPT base address = 0378h.
ECP base address = FFFFFFFFh.
Cable connection established.
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 11/6/2011 4:50:20 PM
// *** BATCH CMD : Identify -inferir
PROGRESS_START - Starting Operation.
Identifying chain contents...done.
ERROR:iMPACT - A problem may exist in the hardware configuration. Check that the cable, scan chain, and power connections are intact, that the specified scan chain configuration matches the actual hardware, and that the power supply is adequate and delivering the correct voltage.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
// *** BATCH CMD : identifyMPM
dose any one know were i am going rong thanks
Welcome to iMPACT
iMPACT Version: 13.3
Project: C:\Xilinx\13.3\ISE_DS\\auto_project.ipf created.
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
// *** BATCH CMD : setMode -bs
Enumerating cables. Please wait.
PROGRESS_START - Starting Operation.
Connecting to cable (Usb Port - USB21).
Checking cable driver.
Source driver files not found.
The Platform Cable USB is not detected. Please connect a cable.If a cable is connected, please disconnect
and reconnect to the usb port, follow the instructions in the 'Found New Hardware Wizard', then retry
the Cable Setup operation.
PROGRESS_END - End Operation.
Elapsed time = 2 sec.
INFO:iMPACT - Digilent Plugin: no JTAG device was found.
// *** BATCH CMD : setCable -target "xilinx_parallel PORT=LPT1 FREQUENCY=2500000"
Connecting to cable (Parallel Port - LPT1).
Checking cable driver.
Driver windrvr6.sys version = 10.2.1.0. WinDriver v10.21 Jungo (c) 1997 - 2010 Build Date: Aug 31 2010 X86 32bit SYS 14:35:41, version = 1021.
LPT base address = 0378h.
ECP base address = FFFFFFFFh.
Cable connection established.
Attempting to identify devices in the boundary-scan chain configuration...
INFO:iMPACT - Current time: 11/6/2011 4:50:20 PM
// *** BATCH CMD : Identify -inferir
PROGRESS_START - Starting Operation.
Identifying chain contents...done.
ERROR:iMPACT - A problem may exist in the hardware configuration. Check that the cable, scan chain, and power connections are intact, that the specified scan chain configuration matches the actual hardware, and that the power supply is adequate and delivering the correct voltage.
PROGRESS_END - End Operation.
Elapsed time = 0 sec.
// *** BATCH CMD : identifyMPM
dose any one know were i am going rong thanks