My DM800 freezes as shown in the picture,ive tried every boot loader from ss53-ss72
The box has previously been working but just stoped booting and started freezing upon boot.
ive used the following images to name but a few.
Nabilo_BlackHole_DM800_RC1.nfi
gemini2-440-dm800_ss69 modified by jams01.nfi
nabilov6bootloader67.nfi
pli-enigma2-jade3-dm800-20090719-6555_8a8f8.nfi
NabiloBlackHole-11-BL72-DM800
I am using dreamup 1.3.3.2 to flash the DM800
even with the recover bad sectors option on in dreamup
I get no error like "no ca found"
I have tried looking for the fault using hypterm (the boot log is below)
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #67 (20081024)
0.000 - BCM board setup
0.022 - fp init
0.023 - ca init
0.399 - load config
dCA: not existent, loading defaults
0.430 - config loaded.
* press to enter setup
OLED found!
BOOT #67(20081024)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 106538
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <[email protected]>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
Done initializing U0
found console= 0
HI WORLD!!!
gathering mode: 0x00000264 at 0x0xb000040c
split mode: 0x00000001 at 0xb0000410
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
cfeBootParms ===>
Number of Nand Chips = 0
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
1 831ffee0 8303ab98
Kernel boot options: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
Initial CP0 22 value : 0x00010020
Updated CP0 22 value : 0x00000020
CP0 reg 22 sel 0 to 5: 0xe3800000 0x00000020 0x00000000 0x00000020 0x00000000 0x00000020
Sundry 0xb0404000, chipId 0x00007401, bcm7401Cx 0x21
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 08000000: RAM]
node [08000000, 08000000: RSVD]
<4>bootmem_init: map 0 type 1
<4>bootmem_init: curr_pfn 0x0000039f last_pfn 0x0000ffff max_low_pfn 0x00010000
<4>bootmem_init: Done
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:31
<7> Normal zone: 0 pages, LIFO batch:1
<7> HighMem zone: 0 pages, LIFO batch:1
Before resource_init
After resource_init
Built 1 zonelists
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
MIPS_CACHE_ALIASES = ON
end of ld_mmu_r4xx0
end of local_tlb_init
Wired: 17
Index: 0 pgmask=16Mb va=d0000000 asid=00
[pa=d0000000 c=2 d=1 v=1 g=1]
[pa=d1000000 c=2 d=1 v=1 g=1]
Index: 1 pgmask=16Mb va=d2000000 asid=00
[pa=d2000000 c=2 d=1 v=1 g=1]
[pa=d3000000 c=2 d=1 v=1 g=1]
Index: 2 pgmask=16Mb va=d4000000 asid=00
[pa=d4000000 c=2 d=1 v=1 g=1]
[pa=d5000000 c=2 d=1 v=1 g=1]
Index: 3 pgmask=16Mb va=d6000000 asid=00
[pa=d6000000 c=2 d=1 v=1 g=1]
[pa=d7000000 c=2 d=1 v=1 g=1]
Index: 4 pgmask=16Mb va=d8000000 asid=00
[pa=d8000000 c=2 d=1 v=1 g=1]
[pa=d9000000 c=2 d=1 v=1 g=1]
Index: 5 pgmask=16Mb va=da000000 asid=00
[pa=da000000 c=2 d=1 v=1 g=1]
[pa=db000000 c=2 d=1 v=1 g=1]
Index: 6 pgmask=16Mb va=dc000000 asid=00
[pa=dc000000 c=2 d=1 v=1 g=1]
[pa=dd000000 c=2 d=1 v=1 g=1]
Index: 7 pgmask=16Mb va=de000000 asid=00
[pa=de000000 c=2 d=1 v=1 g=1]
[pa=df000000 c=2 d=1 v=1 g=1]
Index: 8 pgmask=16Mb va=e0000000 asid=00
[pa=e0000000 c=2 d=1 v=1 g=1]
[pa=e1000000 c=2 d=1 v=1 g=1]
Index: 9 pgmask=16Mb va=e2000000 asid=00
[pa=e2000000 c=2 d=1 v=1 g=1]
[pa=e3000000 c=2 d=1 v=1 g=1]
Index: 10 pgmask=16Mb va=e4000000 asid=00
[pa=e4000000 c=2 d=1 v=1 g=1]
[pa=e5000000 c=2 d=1 v=1 g=1]
Index: 11 pgmask=16Mb va=e6000000 asid=00
[pa=e6000000 c=2 d=1 v=1 g=1]
[pa=e7000000 c=2 d=1 v=1 g=1]
Index: 12 pgmask=16Mb va=e8000000 asid=00
[pa=e8000000 c=2 d=1 v=1 g=1]
[pa=e9000000 c=2 d=1 v=1 g=1]
Index: 13 pgmask=16Mb va=ea000000 asid=00
[pa=ea000000 c=2 d=1 v=1 g=1]
[pa=eb000000 c=2 d=1 v=1 g=1]
Index: 14 pgmask=16Mb va=ec000000 asid=00
[pa=ec000000 c=2 d=1 v=1 g=1]
[pa=ed000000 c=2 d=1 v=1 g=1]
Index: 15 pgmask=16Mb va=ee000000 asid=00
[pa=ee000000 c=2 d=1 v=1 g=1]
[pa=ef000000 c=2 d=1 v=1 g=1]
Index: 16 pgmask=16Mb va=f0000000 asid=00
[pa=f0000000 c=2 d=1 v=1 g=1]
[pa=f1000000 c=2 d=1 v=1 g=1]
$$$$$$$$$$ 1394 dev id ffffffff
$$$$$$$$$$ mini slot dev id ffffffff
$$$$$$$$$$ external dev id ffffffff
$$$$$$$$$$SATA dev id 02421166
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
timer irq 68 end 57
PID hash table entries: 2048 (order: 11, 32768 bytes)
mips_counter_frequency = 148000000 from Calibration, = 148500000 from header(CPU_MHz/2)
Using 148.501 MHz high precision timer.
Console: colour dummy device 80x25
################## brcm_serial_console_init, sercon=80325f50
Has anybody had this problem before and managed to fix it?
or any sugestions on how to fix it?
the box has a sim that enables boot loader 72 in it,
so i dont think its a boot loader problem as i dont get the "no ca found" error
Report this post
The box has previously been working but just stoped booting and started freezing upon boot.
ive used the following images to name but a few.
Nabilo_BlackHole_DM800_RC1.nfi
gemini2-440-dm800_ss69 modified by jams01.nfi
nabilov6bootloader67.nfi
pli-enigma2-jade3-dm800-20090719-6555_8a8f8.nfi
NabiloBlackHole-11-BL72-DM800
I am using dreamup 1.3.3.2 to flash the DM800
even with the recover bad sectors option on in dreamup
I get no error like "no ca found"
I have tried looking for the fault using hypterm (the boot log is below)
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM800
FIRST STAGE 1.00 {BO23456}
2ND STAGE OK, build #67 (20081024)
0.000 - BCM board setup
0.022 - fp init
0.023 - ca init
0.399 - load config
dCA: not existent, loading defaults
0.430 - config loaded.
* press
OLED found!
BOOT #67(20081024)
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++
dreamupd initialized
Scanning JFFS2 FS: . done.
/flash/bootlogo.elf
bootlogo size: 106538
using 1280x720p (60.00 Hz)
Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <[email protected]>
parsing JPEG header..
JPEG Size: 1280x720
/flash/vmlinux.gz
Done initializing U0
found console= 0
HI WORLD!!!
gathering mode: 0x00000264 at 0x0xb000040c
split mode: 0x00000001 at 0xb0000410
board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
Detected 256 MB on board
cfeBootParms ===>
Number of Nand Chips = 0
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
1 831ffee0 8303ab98
Kernel boot options: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
Initial CP0 22 value : 0x00010020
Updated CP0 22 value : 0x00000020
CP0 reg 22 sel 0 to 5: 0xe3800000 0x00000020 0x00000000 0x00000020 0x00000000 0x00000020
Sundry 0xb0404000, chipId 0x00007401, bcm7401Cx 0x21
CPU revision is: 00020000
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
User-defined physical RAM map:
node [00000000, 08000000: RAM]
node [08000000, 08000000: RSVD]
<4>bootmem_init: map 0 type 1
<4>bootmem_init: curr_pfn 0x0000039f last_pfn 0x0000ffff max_low_pfn 0x00010000
<4>bootmem_init: Done
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:31
<7> Normal zone: 0 pages, LIFO batch:1
<7> HighMem zone: 0 pages, LIFO batch:1
Before resource_init
After resource_init
Built 1 zonelists
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
before init RAC 0x02a00000 0x00000000
after init RAC 0x02a0000f 0x0fff0000
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, linesize 16 bytes.
MIPS_CACHE_ALIASES = ON
end of ld_mmu_r4xx0
end of local_tlb_init
Wired: 17
Index: 0 pgmask=16Mb va=d0000000 asid=00
[pa=d0000000 c=2 d=1 v=1 g=1]
[pa=d1000000 c=2 d=1 v=1 g=1]
Index: 1 pgmask=16Mb va=d2000000 asid=00
[pa=d2000000 c=2 d=1 v=1 g=1]
[pa=d3000000 c=2 d=1 v=1 g=1]
Index: 2 pgmask=16Mb va=d4000000 asid=00
[pa=d4000000 c=2 d=1 v=1 g=1]
[pa=d5000000 c=2 d=1 v=1 g=1]
Index: 3 pgmask=16Mb va=d6000000 asid=00
[pa=d6000000 c=2 d=1 v=1 g=1]
[pa=d7000000 c=2 d=1 v=1 g=1]
Index: 4 pgmask=16Mb va=d8000000 asid=00
[pa=d8000000 c=2 d=1 v=1 g=1]
[pa=d9000000 c=2 d=1 v=1 g=1]
Index: 5 pgmask=16Mb va=da000000 asid=00
[pa=da000000 c=2 d=1 v=1 g=1]
[pa=db000000 c=2 d=1 v=1 g=1]
Index: 6 pgmask=16Mb va=dc000000 asid=00
[pa=dc000000 c=2 d=1 v=1 g=1]
[pa=dd000000 c=2 d=1 v=1 g=1]
Index: 7 pgmask=16Mb va=de000000 asid=00
[pa=de000000 c=2 d=1 v=1 g=1]
[pa=df000000 c=2 d=1 v=1 g=1]
Index: 8 pgmask=16Mb va=e0000000 asid=00
[pa=e0000000 c=2 d=1 v=1 g=1]
[pa=e1000000 c=2 d=1 v=1 g=1]
Index: 9 pgmask=16Mb va=e2000000 asid=00
[pa=e2000000 c=2 d=1 v=1 g=1]
[pa=e3000000 c=2 d=1 v=1 g=1]
Index: 10 pgmask=16Mb va=e4000000 asid=00
[pa=e4000000 c=2 d=1 v=1 g=1]
[pa=e5000000 c=2 d=1 v=1 g=1]
Index: 11 pgmask=16Mb va=e6000000 asid=00
[pa=e6000000 c=2 d=1 v=1 g=1]
[pa=e7000000 c=2 d=1 v=1 g=1]
Index: 12 pgmask=16Mb va=e8000000 asid=00
[pa=e8000000 c=2 d=1 v=1 g=1]
[pa=e9000000 c=2 d=1 v=1 g=1]
Index: 13 pgmask=16Mb va=ea000000 asid=00
[pa=ea000000 c=2 d=1 v=1 g=1]
[pa=eb000000 c=2 d=1 v=1 g=1]
Index: 14 pgmask=16Mb va=ec000000 asid=00
[pa=ec000000 c=2 d=1 v=1 g=1]
[pa=ed000000 c=2 d=1 v=1 g=1]
Index: 15 pgmask=16Mb va=ee000000 asid=00
[pa=ee000000 c=2 d=1 v=1 g=1]
[pa=ef000000 c=2 d=1 v=1 g=1]
Index: 16 pgmask=16Mb va=f0000000 asid=00
[pa=f0000000 c=2 d=1 v=1 g=1]
[pa=f1000000 c=2 d=1 v=1 g=1]
$$$$$$$$$$ 1394 dev id ffffffff
$$$$$$$$$$ mini slot dev id ffffffff
$$$$$$$$$$ external dev id ffffffff
$$$$$$$$$$SATA dev id 02421166
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
timer irq 68 end 57
PID hash table entries: 2048 (order: 11, 32768 bytes)
mips_counter_frequency = 148000000 from Calibration, = 148500000 from header(CPU_MHz/2)
Using 148.501 MHz high precision timer.
Console: colour dummy device 80x25
################## brcm_serial_console_init, sercon=80325f50
Has anybody had this problem before and managed to fix it?
or any sugestions on how to fix it?
the box has a sim that enables boot loader 72 in it,
so i dont think its a boot loader problem as i dont get the "no ca found" error
Report this post