Hi
Recently i have purchased growrock gr 100 HD my stb ...when
I updating with new firmware and suddenly it becomes stop and struck
on front panel show boot check the screen shot....
I attach the Hyperterminal and capture bug check it ....
--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul 6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (2076) ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 195749 uSec
U-Boot 1.2.0.0928_a (Secondary Bootloader) (Nov 12 2010 - 14:36:47)
CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x001a4000: bad block
NAND 0x001a8000: bad block
NAND 0x00448000: bad block
so what is the soultion of this problem??
i am waiting for ur good reply.
Recently i have purchased growrock gr 100 HD my stb ...when
I updating with new firmware and suddenly it becomes stop and struck
on front panel show boot check the screen shot....
I attach the Hyperterminal and capture bug check it ....
--------------------------------------------------------------------
-- Generic Primary Bootloader 88.88-8888, NI (10:14:27, Jul 6 2010)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (2076) ST SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 195749 uSec
U-Boot 1.2.0.0928_a (Secondary Bootloader) (Nov 12 2010 - 14:36:47)
CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: ST Micro 64MiB 3,3V 8-bit
NAND 0x001a4000: bad block
NAND 0x001a8000: bad block
NAND 0x00448000: bad block
so what is the soultion of this problem??
i am waiting for ur good reply.
