i have rieciever with this hardware info
--------------------------------------------------------------------
-- Generic Primary Bootloader 0.1-3847, NI (04:13:33, Feb 17 2009)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (AD76) Hynix SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 268521 uSec
U-Boot 1.2.0.0428_a (Secondary Bootloader) (Aug 24 2010 - 11:14:28)
CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 64MiB 3,3V 8-bit
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1114 msec
Hit any key to stop autoboot-----: 1 0
Boot mode is :
Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1704621 Bytes = 1.6 MB
Load Address: 80001000
Entry Point: 802e30f0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
can i flash it with tm image
thnx
--------------------------------------------------------------------
-- Generic Primary Bootloader 0.1-3847, NI (04:13:33, Feb 17 2009)
-- Andre McCurdy, NXP Semiconductors
--------------------------------------------------------------------
Device: PNX8335 M1
Secure boot: disabled, keysel: 0, vid: 0 (expecting 2)
Poly10: 0x00000000
RNG: enabled
RSA keyhide: enabled
UID: 0000000000000000
AES key: 00000000000000000000000000000000
KC status: 0x00000000
Flash config: 7 (omni: 8bit NAND), timing: 0x0C
CPU clock: 320 MHz
SIF0: 512 cols x 8192 rows: 64 MBytes
SIF1: 512 cols x 8192 rows: 64 MBytes
DRAM: 200 MHz, 2 x 64 MBytes: 128 MBytes
NAND: RDY polling disabled
NAND: (AD76) Hynix SLC, pagesize 512, blocksize 16k, 64 MBytes
NAND 0x00020000: valid header
NAND 0x00020000: valid image
aboot exec time: 268521 uSec
U-Boot 1.2.0.0428_a (Secondary Bootloader) (Aug 24 2010 - 11:14:28)
CPU: PNX????
Secure boot: disabled
DRAM: 128 MB
NAND: nCS0 (force asserted legacy mode)
NAND: Hynix 64MiB 3,3V 8-bit
Net: ip3902
Board Opts: EthOsc HDMI PAL
Splash: done
u-boot startup time so far: 1114 msec
Hit any key to stop autoboot-----: 1 0
Boot mode is :
Loading from 64MiB 3,3V 8-bit, offset 0x1020000
Automatic boot of image at addr 0x80800000 ...
## Booting image at 80800100 ...
Image Name: Linux Kernel Image
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 1704621 Bytes = 1.6 MB
Load Address: 80001000
Entry Point: 802e30f0
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
can i flash it with tm image
thnx