rom 10

[slonger]

hi
i have a rom 10 card and infinity usb unlimited and nagraedit 3 and 4.1
in dropdown menu which card do I pick.
I have read to put programmer in phoenix mode then open in nagraedit but nothing happens..

any help please.

 

[brighton mike]

hi
i have a rom 10 card and infinity usb unlimited and nagraedit 3 and 4.1
in dropdown menu which card do I pick.
I have read to put programmer in phoenix mode then open in nagraedit but nothing happens..

any help please.

]]

Is your 9 pin lead connected?

BM

 

[slonger]

its just usb on this programmer

 

[Donnie Darko]

its just usb on this programmer

You need an rs232 serial cable as well.

 

[fatblerk]

You need an rs232 serial cable as well.

This programmer uses a Virtual comm port (VCP)
Make sure you set up the VCP to phoenix 3.68mhz and configuire Nagraedit to the same comm port.

h**p://www.wbe.dk/default.asp?show=supportdetail&ProductID=11&SupportID=18

 

[slonger]

This programmer uses a Virtual comm port (VCP)
Make sure you set up the VCP to phoenix 3.68mhz and configuire Nagraedit to the same comm port.

h**p://www.wbe.dk/default.asp?show=supportdetail&ProductID=11&SupportID=18

yes programmer and nagraedit set to same comm port and in phoenix mode'

do I still need the rs232 lead instead of the usb lead I got with the programmer.

 

[**override**]

yes m8 as fatblerk says the serial is needed for the phoenix side of the proggy...

 

[slonger]

on my programmer I have only one socket which takes a usb b plug
the rs 232 cable is usb to serial cable so won't fit my programmer.

 

[fatblerk]

on my programmer I have only one socket which takes a usb b plug
the rs 232 cable is usb to serial cable so won't fit my programmer.

The unlimited doesn't have a serial connection just a usb port so you can only connect via a usb lead.
You'll need to configuire the VCP to suit the third party software's requirement.

again check out this link http://www.wbe.dk/default.asp?show=supportdetail&ProductID=11&SupportID=18

 

[slonger]

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 31 36 4D
ROM Revision: 010
EEPROM Revision: RevA16
SetIFS failed
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Reading ROM10 failed
Closing of COM1 was successful


this what i get in nagra edit, where * is i do have numbers.
so i think my programmer is set right

 

[brighton mike]

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 31 36 4D
ROM Revision: 010
EEPROM Revision: RevA16
SetIFS failed
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Reading ROM10 failed
Closing of COM1 was successful


this what i get in nagra edit, where * is i do have numbers.
so i think my programmer is set right

Try a repair with MROM, you might need to use XNCS to obtain your keys afterwards

Regards

BM :santa:

 

[fatblerk]

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 31 36 4D
ROM Revision: 010
EEPROM Revision: RevA16
SetIFS failed
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Reading ROM10 failed
Closing of COM1 was successful


this what i get in nagra edit, where * is i do have numbers.
so i think my programmer is set right

Load xncs then goto options>settings and check everything except ghost must be in eeprom then dump the card ....... your BD keys 0 to 3 should be in lines C040 to C070 respectively.
You should then armed with these keys be able to dump the card in nagraedit

 

[slonger]

gee i'm glad you guys are here , my brain is hurting now.
tryed mrom repair still same in nagraedit is there a english version of mrom.
in xncs it says no atr sent.

 

[fatblerk]

gee i'm glad you guys are here , my brain is hurting now.
tryed mrom repair still same in nagraedit is there a english version of mrom.
in xncs it says no atr sent.

Are you still getting the ATR string when you reset/attempt to open the card with Nagraedit?

 

[slonger]

just tried again with nagraedit and i get as follows

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 30 20 52 65 76 41 31 36 4D
ROM Revision: 010
EEPROM Revision: RevA16
SetIFS failed
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Reading ROM10 failed
Closing of COM1 was successful


i do get numbers where * 's are

 

[carwash]

Hi m8"!

When you get a SetIFS Failed It means it doesnt know the size of the dataspace

SetIFS is the blocksize maximum packet size that the card sends responses back to Nagra Edit, etc

The Default is fairly low, so nagraedit issues a command to increase the IFS. That way it can read or write all the data in the card ((64 bytes)) . The problem you are experiencing is due to the card not responding correctly to the command to increase the IFS. It could be due to communication errors on your serial port, power supply, or something in the card (Data Corrupted).. Try increasing the retry count in Nagra Edit ((Preferences)) and see if it can get through it..
If increasing the retry doesn't work.. lower the FIFO buffers of the COM Port as low as you can (windows setting)(last resort). If that doesn't work... try the same card on a different reader/writer or computer.
I used to get quite a few SetIFS fails but since i changed programmer i have had no problems at all

BTW: It’s my opinion that rom cards including software like Nagraedit don’t Like USB connections
But then again it's only a opinion"!!!!

 

[slonger]

thanks for the time you have taken for all your replies still no further on..

 

[spud1966]

Hi slonger

Try this it night work????? for your BD3 key , close nagraedit program , then run it again and use this for your BD3 key CB C6 69 DE D2 0F 40 52 7C CA FF 32 1F F4 F8 06

Make sure you put the key into the bottom one!!!!!!!!!!!

Cheers Garry

 

[slonger]

hi Gary
I don't get anything in data editor ..

 

[spud1966]

Hi slonger

Never read you thread correctly lol , hope you sort it out m8........

Cheers Garry