Ambit 100 a bit of help please.

stellarocksme

DW Regular
Joined
Jun 6, 2005
Messages
1,139
Reaction score
60
Location
on here
Ok i've mad my max233 :Jester: im following the newbie ntl tutorial form the download section, here's where i get stuck....


Ambit Cable Modem Console Management
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is 00:05:3A:F3:4F:EE
This board's USB Interface hardware address is 00:01:2A:60:EF:16
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.100]
The file to download and start is C2403225.cpr
--------------------------------------------------------------------------

1) set Image1 Primary
2) set Image2 Primary
3) Download Image1
4) Download Image2
5) Download BootCode
6) Parameters Setup
99) Exit

Choice : 99


Choose option 99, this will exit the program and reboot your modem with your new Mac address active.

So press 99 then get this .....

Detect MXIC MX219LV160B Flash

Running image2 !!!!!

BCM3345 Image
S12ce7865 ##ECS Magic number was wrong. Working with default value.
Detect MXIC MX219LV160B Flash
<USB ni init>
Location of Root is 80105560
Running from RAM
Detect MXIC MX219LV160B Flash
ROM MAC ADDR: 0002:8a61:5dbc
This is image2
Detect a filesystem
This code version is 4684.2.1.8.2.22.3215 Dual Mode
DNS service enable
CM application's DNS en
DHCP Server init (Use Default)
Add CM[00:02:8a:61:5d:bc] to DA filter
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue software reset
Waiting for reset finished
Init EMAC registers
USBD started

DUSB NDIS Driver
USB bMacAddress: 00D059E87C05
USB Vendor ID: b20b, deviceid: 9860
Reading programmed USB Configuration...
owUSB init OK
nstreamInit Mibs
frequency is 402750000 Hz
Annex B mode selected
Downstream symbol rate is 5056941 symbols per second
Test port setting is 0x00
Initial upstream powe
Send encryption key requests
Use DHCP
VoIP card interface is NOT enabled.
The tuner is a Temic 4937_8769
The upstream amplifier is a MicroTune 1530
The downstream reference frequency is 24.500 MHz
The upstream reference frequency is 28.000 MHz
The input frequency to the 3300 is 43.750 MHz
Stored upstream channel ID is 0x04
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
SetTXPower 46.00 (46.000000)
sid == ffffffff

Hit a key in 2 seconds to enter

FreqPlans[0] = 8
FreqPlans[1] = 7
numFreqPlan = 2
Noise
FreqPlan Scanning .... Preset(History)Table
Check Freq of 402750000 hz... No Power...nuthin!
FreqPlan Scanning .... Customer Specified
MaxChannelNum == 6
Check Freq of 402750000 hz... No Power...nuthin!
Check Freq of 586750000 hz... No Power...nuthin!
Check Freq of 475750000 hz... No Power...nuthin!
Check Freq of 481750000 hz... No Power...nuthin!
Check Freq of 487750000 hz... No Power...nuthin!
Check Freq of 493750000 hz... No Power...nuthin!
fpindex = 0
FreqPlan Scanning .... PAL-I HRC
MaxChannelNum == 95
Check Freq of 402750000 hz... No Power...nuthin!
Check Freq of 410750000 hz... No Power...nuthin!
Check Freq of 418750000 hz... No Power...nuthin!
Check Freq of 426750000 hz... No Power...nuthin!
Check Freq of 434750000 hz... No Power...nuthin!
Check Freq of 442750000 hz... No Power...nuthin!
Check Freq of 450750000 hz... No Power...nuthin!
Check Freq of 458750000 hz... No Power...nuthin!
Check Freq of 466750000 hz... No Power...nuthin!
Check Freq of 474750000 hz... No Power...nuthin!
Check Freq of 482750000 hz... No Power...nuthin!
Check Freq of 490750000 hz... No Power...nuthin!
Check Freq of 498750000 hz... No Power...nuthin!
Check Freq of 506750000 hz... No Power...nuthin!
Check Freq of 514750000 hz... No Power...nuthin!
Check Freq of 522750000 hz... No Power...nuthin!
Check Freq of 530750000 hz... No Power...nuthin!
Check Freq of 538750000 hz... No Power...nuthin!
Check Freq of 546750000 hz... No Power...nuthin!
Check Freq of 554750000 hz.
Check Freq of 562750000 hz... No Power...nuthin!
Check Freq of 570750000 hz... No Power...nuthin!
Check Freq of 578750000 hz... No Power...nuthin!
Check Freq of 586750000 hz... No Power...nuthin!
Check Freq of 594750000 hz... No Power...nuthin!
Check Freq of 602750000 hz... No Power...nuthin!
Check Freq of 610750000 hz... No Power...nuthin!
Check Freq of 618750000 hz... No Power...nuthin!
Check Freq of 626750000 hz... No Power...nuthin!
Check Freq of 634750000 hz... No Power...nuthin!
Check Freq of 642750000 hz.
Check Freq of 650750000 hz... No Power...nuthin!
Check Freq of 658750000 hz... No Power...nuthin!
Check Freq of 666750000 hz... No Power...nuthin!
Check Freq of 674750000 hz... No Power...nuthin!
Check Freq of 682750000 hz... No Power...nuthin!
Check Freq of 690750000 hz... No Power...nuthin!
Check Freq of 698750000 hz... No Power...nuthin!
Check Freq of 706750000 hz... No Power...nuthin!




Just keeps going, any idea's people, If i connect it to my pc via ethernet any tpye 192.168.100.1 i just get Cannot be displayed?
Mmmmm anybody ?
 

L33tpL4y4

Inactive User
Joined
Jul 27, 2005
Messages
1,097
Reaction score
1
stellarocksme said:
Ok i've mad my max233 :Jester: im following the newbie ntl tutorial form the download section, here's where i get stuck....


Ambit Cable Modem Console Management
--------------------------------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is 00:05:3A:F3:4F:EE
This board's USB Interface hardware address is 00:01:2A:60:EF:16
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.100]
The file to download and start is C2403225.cpr
--------------------------------------------------------------------------

1) set Image1 Primary
2) set Image2 Primary
3) Download Image1
4) Download Image2
5) Download BootCode
6) Parameters Setup
99) Exit

Choice : 99


Choose option 99, this will exit the program and reboot your modem with your new Mac address active.

So press 99 then get this .....

Detect MXIC MX219LV160B Flash

Running image2 !!!!!

BCM3345 Image
S12ce7865 ##ECS Magic number was wrong. Working with default value.
Detect MXIC MX219LV160B Flash
<USB ni init>
Location of Root is 80105560
Running from RAM
Detect MXIC MX219LV160B Flash
ROM MAC ADDR: 0002:8a61:5dbc
This is image2
Detect a filesystem
This code version is 4684.2.1.8.2.22.3215 Dual Mode
DNS service enable
CM application's DNS en
DHCP Server init (Use Default)
Add CM[00:02:8a:61:5d:bc] to DA filter
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue software reset
Waiting for reset finished
Init EMAC registers
USBD started

DUSB NDIS Driver
USB bMacAddress: 00D059E87C05
USB Vendor ID: b20b, deviceid: 9860
Reading programmed USB Configuration...
owUSB init OK
nstreamInit Mibs
frequency is 402750000 Hz
Annex B mode selected
Downstream symbol rate is 5056941 symbols per second
Test port setting is 0x00
Initial upstream powe
Send encryption key requests
Use DHCP
VoIP card interface is NOT enabled.
The tuner is a Temic 4937_8769
The upstream amplifier is a MicroTune 1530
The downstream reference frequency is 24.500 MHz
The upstream reference frequency is 28.000 MHz
The input frequency to the 3300 is 43.750 MHz
Stored upstream channel ID is 0x04
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
SetTXPower 46.00 (46.000000)
sid == ffffffff

Hit a key in 2 seconds to enter

FreqPlans[0] = 8
FreqPlans[1] = 7
numFreqPlan = 2
Noise
FreqPlan Scanning .... Preset(History)Table
Check Freq of 402750000 hz... No Power...nuthin!
FreqPlan Scanning .... Customer Specified
MaxChannelNum == 6
Check Freq of 402750000 hz... No Power...nuthin!
Check Freq of 586750000 hz... No Power...nuthin!
Check Freq of 475750000 hz... No Power...nuthin!
Check Freq of 481750000 hz... No Power...nuthin!
Check Freq of 487750000 hz... No Power...nuthin!
Check Freq of 493750000 hz... No Power...nuthin!
fpindex = 0
FreqPlan Scanning .... PAL-I HRC
MaxChannelNum == 95
Check Freq of 402750000 hz... No Power...nuthin!
Check Freq of 410750000 hz... No Power...nuthin!
Check Freq of 418750000 hz... No Power...nuthin!
Check Freq of 426750000 hz... No Power...nuthin!
Check Freq of 434750000 hz... No Power...nuthin!
Check Freq of 442750000 hz... No Power...nuthin!
Check Freq of 450750000 hz... No Power...nuthin!
Check Freq of 458750000 hz... No Power...nuthin!
Check Freq of 466750000 hz... No Power...nuthin!
Check Freq of 474750000 hz... No Power...nuthin!
Check Freq of 482750000 hz... No Power...nuthin!
Check Freq of 490750000 hz... No Power...nuthin!
Check Freq of 498750000 hz... No Power...nuthin!
Check Freq of 506750000 hz... No Power...nuthin!
Check Freq of 514750000 hz... No Power...nuthin!
Check Freq of 522750000 hz... No Power...nuthin!
Check Freq of 530750000 hz... No Power...nuthin!
Check Freq of 538750000 hz... No Power...nuthin!
Check Freq of 546750000 hz... No Power...nuthin!
Check Freq of 554750000 hz.
Check Freq of 562750000 hz... No Power...nuthin!
Check Freq of 570750000 hz... No Power...nuthin!
Check Freq of 578750000 hz... No Power...nuthin!
Check Freq of 586750000 hz... No Power...nuthin!
Check Freq of 594750000 hz... No Power...nuthin!
Check Freq of 602750000 hz... No Power...nuthin!
Check Freq of 610750000 hz... No Power...nuthin!
Check Freq of 618750000 hz... No Power...nuthin!
Check Freq of 626750000 hz... No Power...nuthin!
Check Freq of 634750000 hz... No Power...nuthin!
Check Freq of 642750000 hz.
Check Freq of 650750000 hz... No Power...nuthin!
Check Freq of 658750000 hz... No Power...nuthin!
Check Freq of 666750000 hz... No Power...nuthin!
Check Freq of 674750000 hz... No Power...nuthin!
Check Freq of 682750000 hz... No Power...nuthin!
Check Freq of 690750000 hz... No Power...nuthin!
Check Freq of 698750000 hz... No Power...nuthin!
Check Freq of 706750000 hz... No Power...nuthin!




Just keeps going, any idea's people, If i connect it to my pc via ethernet any tpye 192.168.100.1 i just get Cannot be displayed?
Mmmmm anybody ?
Hit any key when it says!
 

Monty

Member ++
Joined
Oct 25, 2004
Messages
424
Reaction score
3
Why do you type 99 and exit ?

Press 6 enter Parameters and change mac address.
 

nilrem

Inactive User
Joined
Mar 10, 2005
Messages
921
Reaction score
9
Thats if the firmware hasn't already been updated that is :)

Cheers
 
TEST
Top