I got a sammy 2110C box i have the orignal Card. Im trying to glitch it so i can read the card in Nagra but ive been trying for last couple hours and im struggling. Im gonna explain how i do it Step by step plz tell me if im wrong
I have the TMC911 unlooper so what i do is there is a switch near the power supply i put that to the left. I also put switches 1 and 5 to on.
I flash the looper wit XP Atmel programmer i get this message.
Hex Files Loaded.
Initializing ...
Initialized
Syncing ...
Synchronized
Vendor Code: 00 (Unknown)
Part Family: 01 DEVICE LOCKED
Issuing Chip Erase ...
Erased
Vendor Code: 1e (Atmel)
Part Family: 91 AT90S2313
Programming EEPROM ...
Programming Flash ...
Verifying EEPROM ...
Verifying Flash ...
Setting Lock Bits ...
Lock Bits Set!
Complete!
I take it thats ok... Then i push the switch back to the right and push Switch 1 down and push Switch 2 up. So that switch 2 and 5 are on only. Is this right?
then i install sct10en.exe (windows scrip control) and install that.
Then i run Winexp (both nagra and winexp in 98 mode). in the config settings i select the modded T911 ( i got the config file from the tutorial in the download section.
Then i open up a script (i load rom11 unlocker script)
I hit the execute button and i get this
________________Setting up WinExplorer_________________
TX Data : 19 03 15 60 10 21 00 0D A0 CA 00 00 07 21 05 06
03 FF FF 00 20 40 0E 05 9F 00
RX Data : 0A 00
Script C:\Documents and Settings\A Y A A Z\Desktop\bod unlocker\rom11 unlocker.xvb Transmission Completed
A box pops up saying unable to find provider..... Exiting
So im kind of left confused pulling my hair out. I then try to read the card in Nagra and i get this error
Opening of COM4 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 31 20 52 65 76 42 30 44 3C
ROM Revision: 011
EEPROM Revision: RevB0D
ProviderID: 5C
CamID: 27 7F C0 13
Using BD3 Key: 4E 69 70 50 45 72 20 49 73 20 61 20 62 75 54 74
Attempting to login to BD3
Reading ROM11 failed
Closing of COM4 was successful
I use the pheonix programmer and i have it in pheonix mode 3.68 (also tried 3.58). Software version for pheonix i use is 1.35 version build 1313 release.
What am i doing wrong? Would appreciate the replies thanks
I have the TMC911 unlooper so what i do is there is a switch near the power supply i put that to the left. I also put switches 1 and 5 to on.
I flash the looper wit XP Atmel programmer i get this message.
Hex Files Loaded.
Initializing ...
Initialized
Syncing ...
Synchronized
Vendor Code: 00 (Unknown)
Part Family: 01 DEVICE LOCKED
Issuing Chip Erase ...
Erased
Vendor Code: 1e (Atmel)
Part Family: 91 AT90S2313
Programming EEPROM ...
Programming Flash ...
Verifying EEPROM ...
Verifying Flash ...
Setting Lock Bits ...
Lock Bits Set!
Complete!
I take it thats ok... Then i push the switch back to the right and push Switch 1 down and push Switch 2 up. So that switch 2 and 5 are on only. Is this right?
then i install sct10en.exe (windows scrip control) and install that.
Then i run Winexp (both nagra and winexp in 98 mode). in the config settings i select the modded T911 ( i got the config file from the tutorial in the download section.
Then i open up a script (i load rom11 unlocker script)
I hit the execute button and i get this
________________Setting up WinExplorer_________________
TX Data : 19 03 15 60 10 21 00 0D A0 CA 00 00 07 21 05 06
03 FF FF 00 20 40 0E 05 9F 00
RX Data : 0A 00
Script C:\Documents and Settings\A Y A A Z\Desktop\bod unlocker\rom11 unlocker.xvb Transmission Completed
A box pops up saying unable to find provider..... Exiting
So im kind of left confused pulling my hair out. I then try to read the card in Nagra and i get this error
Opening of COM4 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 31 20 52 65 76 42 30 44 3C
ROM Revision: 011
EEPROM Revision: RevB0D
ProviderID: 5C
CamID: 27 7F C0 13
Using BD3 Key: 4E 69 70 50 45 72 20 49 73 20 61 20 62 75 54 74
Attempting to login to BD3
Reading ROM11 failed
Closing of COM4 was successful
I use the pheonix programmer and i have it in pheonix mode 3.68 (also tried 3.58). Software version for pheonix i use is 1.35 version build 1313 release.
What am i doing wrong? Would appreciate the replies thanks