Finally got the dm800se to see the tuner but do not see it with eingma2 or on the screen. Below is the log when I plug it in. Why does it not show up?
44.590000] usb 1-1: new high speed USB device using brcm-ehci and address 4
[ 45.446000] hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad?
[ 45.549000] usb 1-1: new high speed USB device using brcm-ehci and address 5
[ 45.665000] usb 1-1: configuration #1 chosen from 1 choice
[ 45.666000] dvb-usb: found a 'Prof 7500 USB DVB-S2' in cold state, will try to load a firmware
[ 45.718000] dvb-usb: downloading firmware from file 'dvb-usb-p7500.fw'
[ 45.720000] dw2102: start downloading DW210X firmware
May 24 21:46:32 dm800se user.notice firmware.sh[1177]: udev firmware loader misses sysfs directory
[ 45.835000] dvb-usb: found a 'Prof 7500 USB DVB-S2' in warm state.
[ 45.836000] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
l: [ 45.839000] DVB: registering new adapter (Prof 7500 USB DVB-S2)
May 24 12:46:34 dm800se user.info kernel: [ 47.889000] dvb-usb: MAC address: 87d969b4M
May 24 12:46:34 dm800se user.debug kernel: [ 47.891000] stv0900_init_internal
May 24 12:46:34 dm800se user.debug kernel: [ 47.891000] stv0900_init_internal: Create New Internal Structure!
May 24 12:46:35 dm800se user.debug kernel: [ 48.854000] stv0900_st_dvbs2_single
May 24 12:46:35 dm800se user.debug kernel: [ 48.854000] stv0900_stop_all_s2_modcod
May 24 12:46:35 dm800se user.debug kernel: [ 48.918000] stv0900_activate_s2_modcod_single
May 24 12:46:36 dm800se user.debug kernel: [ 49.090000] stv0900_set_ts_parallel_serial
May 24 12:46:36 dm800se user.debug kernel: [ 49.278000] stv0900_set_mclk: Mclk set to 135000000, Quartz = 27000000
May 24 12:46:36 dm800se user.debug kernel: [ 49.314000] stv0900_get_mclk_freq: Calculated Mclk = 135000000
May 24 12:46:36 dm800se user.debug kernel: [ 49.366000] stv0900_get_mclk_freq: Calculated Mclk = 135000000
May 24 12:46:36 dm800se user.debug kernel: [ 49.366000] stv0900_attach: Attaching STV0900 demodulator(0)
May 24 12:46:36 dm800se user.info kernel: [ 49.366000] dw2102: Attached STV0900+STB6100A!
dm800se user.warn kernel: [ 49.366000]
49.366000] DVB: registering adapter 1 frontend 0 (STV0900 frontend)...
49.368000] input: IR-receiver inside an USB DVB receiver as /class/input/input6
49.369000] dvb-usb: schedule remote query interval to 150 msecs.
49.370000] dvb-usb: Prof 7500 USB DVB-S2 successfully initialized and connected.
