Super_LFC
Banned
ok hi all im new to this hope you are all doing better than me
ok
i have two ambit modems 1x 120 and 1x 200
after building the max232 getting it all working i cant do anymore it reads the 120 fine but i cant change anything it just keeps running and running I cant stop it to change anything and the 200 does nothing i think its been wiped clean i get nothing it dont even boot up like my 120 does what im asking is can any one help me to get one of them working again i stuck and dont now what to do
Thanks you all
MJ
and it say all this ?
BCM3345
134ce7865
Boot Code SW Version 3.11.3
BCM3345 Ambit
S12ce7865Detect MXIC MX219LV160B Flash
Ambit Cable Modem Console Management
----------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is **********:64
This board's USB Interface hardware address is **********:65
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.100]
The file to download and start is ntlhm120_ntl0001.cpr
--------------------------------------------------------------------------
To change any of this, press any key
Detect MXIC MX219LV160B Flash
Running image1 !!!!!
BCM3345 Image
S12ce7865Detect MXIC MX219LV160B Flash
##ECS Magic number was wrong. Working with default value.
Updating parameter storage. This may take a while...
<USB ni init>
Location of Root is 80105ae0
Running from RAM
Detect MXIC MX219LV160B Flash
This is image1
Detect a filesystem
No way to recover the modem due to a fake USB mac.
DNS service enable
DHCP Server init (Use Default)
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue softw
Waiting for reset finished
Init EMAC registers
USBD started
SenUSB NDIS Driver
Reading programmed USB Configuration...
USB_RESET_RECV
USB init OK
d encryptiInit Mibs
on key requests
Use DHCP
VoIP card interface is NOT enabled.
The tuner is a TEMIC_4907_8768
The upstream amplifier is a MicroTune 1530
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
ok
i have two ambit modems 1x 120 and 1x 200
after building the max232 getting it all working i cant do anymore it reads the 120 fine but i cant change anything it just keeps running and running I cant stop it to change anything and the 200 does nothing i think its been wiped clean i get nothing it dont even boot up like my 120 does what im asking is can any one help me to get one of them working again i stuck and dont now what to do
Thanks you all
MJ
and it say all this ?
BCM3345
134ce7865
Boot Code SW Version 3.11.3
BCM3345 Ambit
S12ce7865Detect MXIC MX219LV160B Flash
Ambit Cable Modem Console Management
----------------------------------------------------
NETWORK INTERFACE PARAMETERS:
IP address on LAN is 192.168.100.1
LAN interface's subnet mask is 255.255.255.0
HARDWARE PARAMETERS:
This board's Ethernet hardware address is **********:64
This board's USB Interface hardware address is **********:65
CABLE MODEM APPLICATION PARAMETERS:
IP address of the TFTP host is [62.253.189.100]
The file to download and start is ntlhm120_ntl0001.cpr
--------------------------------------------------------------------------
To change any of this, press any key
Detect MXIC MX219LV160B Flash
Running image1 !!!!!
BCM3345 Image
S12ce7865Detect MXIC MX219LV160B Flash
##ECS Magic number was wrong. Working with default value.
Updating parameter storage. This may take a while...
<USB ni init>
Location of Root is 80105ae0
Running from RAM
Detect MXIC MX219LV160B Flash
This is image1
Detect a filesystem
No way to recover the modem due to a fake USB mac.
DNS service enable
DHCP Server init (Use Default)
4 Upstream Queues Configured.
Creating USB task
Flushing event log
Issue softw
Waiting for reset finished
Init EMAC registers
USBD started
SenUSB NDIS Driver
Reading programmed USB Configuration...
USB_RESET_RECV
USB init OK
d encryptiInit Mibs
on key requests
Use DHCP
VoIP card interface is NOT enabled.
The tuner is a TEMIC_4907_8768
The upstream amplifier is a MicroTune 1530
Periodic ranging timeouts are enabled
Preamble type will be set by the burst profiles
Use default MCNS symbol rates.
Last edited: