rom11 bo4 problem card

[dave_c]

no matter what i try to open this card it just wont have it , have ran it through mrom , and dc2 through nagra , but everytime i put it in nagra to read the card , it still asks for the backdoor 0 login password

after running dc2 in nag as follows

~~~~~~~~~~~
SUCCESS!!!!
~~~~~~~~~~~
BACKDOORS_1_AND_3_SET_T0
*************************

wen tryin to readin nag edit straight after

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 31 20 52 65 76 42 30 34 4C
ROM Revision: 011
EEPROM Revision: RevB04
ProviderID: **
CamID: ** ** ** **
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Attempting to login to BD3
BackDoor login verified
Dumping Dataspace
Backdoor retrieval has been blocked
Attempting to login to BD3
Attempting to login to BD0
Unable to login, bad password detected
Login attempt aborted
Reading ROM11 failed
Closing of COM1 was successful

 

[shadow]

Have you tried it through XNCS1.8 yet?

 

[irratic]

no matter what i try to open this card it just wont have it , have ran it through mrom , and dc2 through nagra , but everytime i put it in nagra to read the card , it still asks for the backdoor 0 login password

after running dc2 in nag as follows

~~~~~~~~~~~
SUCCESS!!!!
~~~~~~~~~~~
BACKDOORS_1_AND_3_SET_T0
*************************

wen tryin to readin nag edit straight after

Opening of COM1 was successful
ATR String: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50
30 31 31 20 52 65 76 42 30 34 4C
ROM Revision: 011
EEPROM Revision: RevB04
ProviderID: **
CamID: ** ** ** **
Using BD3 Key: ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **
Attempting to login to BD3
BackDoor login verified
Dumping Dataspace
Backdoor retrieval has been blocked
Attempting to login to BD3
Attempting to login to BD0
Unable to login, bad password detected
Login attempt aborted
Reading ROM11 failed
Closing of COM1 was successful

did you have success threw mrom mate?? 300-0-300

 

[dave_c]

@ shadow

in xncs1.8 1 card goes through with the following

Card info retrieved
--------------------------------------------------------------------
1) Calibration is: 3391.58931049799 Mhz , Acc:5,Use Tsc:Yes
2) Building Bug Table...
2) Using Simple Send method!
3) Encrypting Ecm...
--------------------------------------------------------------------
Found the Delay for 1000 @ Time:157000
Found the Delay for 100 @ Time:156600
Found the Delay for 10 @ Time:156560
4) Now Working - Dont Interrupt!
--------------------------------------------------------------------
HeHeHe....Seems the Rom Is Open @ Time:156566 !!!


the other comes up with

Card info retrieved
--------------------------------------------------------------------
1) Calibration is: 3391.58931049799 Mhz , Acc:5,Use Tsc:Yes
2) Building Bug Table...
2) Using Simple Send method!
3) Encrypting Ecm...
--------------------------------------------------------------------
setifs failed

@ irratic

in mrom with the settings u sugested

the card that went through fine on xncs errors on string 4 , but the card that gave a setifs in xncs went through fine on ur settings in mrom

still getting it asking for a bdo when tryin to read through nagra

 

[irratic]

have you tried ticking dump with cmd bug . only in settings in xncs read card then note the bd keys..????

 

[shadow]

In xncs if you go into settings and tick everything it will read your card including bdo keys. you can see these by going into tools and selecting change bd keys.

You can use these in nagra to read the card, but if you still have no luck and mrom is still giving an error on you may have a corrupt card

 

[irratic]

sometimes mrom will give you errors, just run it threw again, sometime takes a couple of goes for it to go.. if you still have probs alter your delays to 280-50-280 and try that..

 

[dave_c]

when i click on eeprom in xncs its all blank

 

[irratic]

click tools and it says change bd keys. click that and you'll see the bd keys

 

[irratic]

did the card dump in xncs??

 

[dave_c]

i clicked on change bd keys and a indow pops up but alllines are blank , and eeprom is also blank

this is all i get when put card in xncs

Retrieving card info...
Card info retrieved
--------------------------------------------------------------------
1) Calibration is: 3391.58876951655 Mhz , Acc:5,Use Tsc:Yes
2) Building Bug Table...
2) Using Simple Send method!
3) Encrypting Ecm...
--------------------------------------------------------------------
Found the Delay for 1000 @ Time:157000
HeHeHe....Seems the Rom Is Open @ Time:157000 !!!

 

[dave_c]

if i click on card and read eeprom i get the following

Retrieving card info...
Card info retrieved
Installing ghost provider...
1.Dumping dataspace...
2.Adding Ghost...
3.Writing DataSpace...
Ghost installed...
Proceeding With Normal Dump...
Send_Iso: Error!
Dumping card,try #0.
Dumping card,try #1.
Send_Iso: Error!
Dumping card,try #2.
Dumping card,try #3.
Couldnt Dump Card...

 

[irratic]

you must of left ghost ticked in the settings mate.. tick all except anything that says ghost then try to read and post the output

 

[dannyrp03]

had probs with mrom and xncs in the past ,but have been using cardtolls in downloads section (faultless so far),give it a go , best regards danny

 

[dave_c]

@ irratic , still comes up the same result as posted before mate

 

[irratic]

not sure if you're supposed to run that image threw sidewinder , but maybe worth a go.. perhaps someone else could advise if its ok...

 

[irratic]

is this the card that goes threw mrom??? or do you get errors??

 

[dave_c]

yep im tryin the card that goes through mrom with no errors

 

[irratic]

run it threw again mate. same settings as befor..then try nagra

 

[dave_c]

have tried it about 10 times , same results every time