Is my kids Nokia dead?

[witchy]

Kids were watching the box tonight, they said it froze then reboot itself, while trying to reboot it locked up on the boot logo so I reflashed the box and now I'm getting 'Waiting for Time' on all channels, I also get an error when I try to run a channel scan.

Is the tuner faulty?

debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0 mID 01
debug: feID 7a gtxID 0b
debug: fpID 5a dsID 01-15.71.1b.07.00.00-fb
debug: HWrev X5 SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032

will verify ELF image, start= 0x800000, size= 154180
verify sig: 262
Branching to 0x40000


U-Boot 1.2.0 (Tuxbox) (Mar 17 2007 - 05:47:42)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ........ done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 650893 bytes loaded to 0x100000
............................................................... done
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 650829 Bytes = 635.6 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.34-dbox2 (dietmarw@globalscum) (gcc version 3.4.4) #3 Sa Mr 17
05:48:19 CET 2007
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/mtdblock2 rw rootfstype=jffs2
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.76 BogoMIPS
Memory: 30864k available (1104k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1c:84:26
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "root (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 11, console /dev/console: '/etc/init.d/rcS'lti-call
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.10 2006/10/04 00:36:41 carjay Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of DBox2 IDE CPLD is at: 0xc3890000
dboxide: probing dbox2 IDE CPLD: walking bit test failed: fffffffe != fbffffdc
dboxide: not a valid dbox2 IDE CPLD detected
Journalled Block Device driver loaded
insmod: xfs.o: no module by that name found
mount: Mounting /dev/ide/host0/bus0/target0/lun0/part2 on /hdd failed: No such f
ile or directory
route: SIOC[ADD|DEL]RT: Network is unreachable
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Detected STB:
Vendor: Nokia
Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)... <<<DOESNT THIS MEAN THAT THE TUNER IS OK???
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v001A
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Starting the automounter
Starting pid 130, console /dev/console: '/etc/init.d/start'

Please press Enter to activate this console. Thu Jan 1 01:00:00 GMT 1970
$Id: sectionsd.cpp,v 1.236 2007/02/25 20:51:52 guenther Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
Please wait newcamd (max. 5 Seconds)
newcamd started successfully
$Id: zapit.cpp,v 1.393 2007/02/28 04:53:26 Arzka Exp $
[newcamd-v6.10b 01:00:08] compiled May 9 2006, 17:19:17
[newcamd-v6.10b 01:00:08] Warning: Error opening config file /var/tuxbox/config/
newcamd/newcamd.conf, using defaults.
[newcamd-v6.10] CA_SEND_MSG: Remote I/O error
[newcamd-v6.10b 01:00:08] Warning: ca device init failed. Slot1 card will be dis
abled
[newcamd-v6.10b 01:00:08] loading keys and roms
[newcamd-v6.10b 01:00:08] Warning: File /var/tuxbox/scce/ppua couldn't be opened
.
[newcamd-v6.10b 01:00:08] rsakeylist:26 parse error
[newcamd-v6.10b 01:00:08] Warning: File /var/tuxbox/scce/tpscrypt couldn't be op
ened.
/tmp/currentservices.xml: No such file or directory
[newcamd-v6.10b 01:00:09] nagra au supports roms: 3 7 10 11
[newcamd-v6.10b 01:00:09] keys and roms loaded
$Id: controld.cpp,v 1.125 2006/09/24 09:17:10 barf Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[yhttpd] Webserver nhttpd/3.1.2 (yhttpd_core/1.2.0)

 

[niteflite01]

Yet another Nokia bites the dust. This is getting unbelievable now. In the last week there have been so, so many Nokias then have gone kaput!

Anyway :

"[newcamd-v6.10] CA_SEND_MSG: Remote I/O error"

...doesn't look good mate. I think that can and usually does indicate some kind of SEC chip error or failure.

 

[witchy]

I'm also getting this when I change channels...

[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
zap failed!
[sectionsd] getUTC: read: Connection timed out
[LCDFONT] FTC_Face_Requester (Fix12/Regular)
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
zap failed!
[sectionsd] getUTC: read: Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
zap failed!
[sectionsd] getUTC: read: Connection timed out
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
zap failed!
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
zap failed!
[sectionsd] getUTC: read: Connection timed out

 

[niteflite01]

Yeah, it definitely looks to me like there's either a problem with your SEC chip (anything from a knackered one, to a dry joint in the area) or perhaps some dodgy memory on the blink.

I could be wrong of course, there are loads here who know more than me obviously, but that's what it looks like mate

The zap failed message is basically the software complaining that it's not getting a usable or understandable signal.

 

[flickster]

hi witchey,,does it have that little memory board plugged in?(some nokias have them) might have come loose,or, try another image, i got the blade trinity working great with a box that was fooked with any sportster image

 

[witchy]

No extra ram board mate and I've already tried 3 different independant images, 2 neutrino and 1 Enigma.

Looks like I now own a large black ashtray.