ok guys here is how to dump ur sammy
first u need a usb jtag
i used this 1
and it would be helpfull if u install a 2x10 pin header
ok once u got the pinheader installed and have the usb jtag
u need to download the following drivers
also u will need hexworkshop or anyother hex file editor u like
and u will need openocd r717 that i have attached to this thread.
once drivers are installed
put the openocd folder into C:\program files
plug jtag into box and pc
power on the box WITH card inserted and on Stream
once box is powered up go to a pay channel
open up a command window type the following command:
now u need to enter this command:
now if everything is working u should get the following
and the box would have rebooted and stuck on pl30 or similar
now u need to use putty (included in openocd-r717 folder)
choose telnet and enter the following:
it should say the following in putty:
Open On-Chip Debugger
>
now u type the following command
now it will start dumping the ram should take around 20 / 30mins
once its dumped the ram
u need to close putty and command window
unplug box take scart out and unplug usb cable from pc
then repeat the steps 3 times remember same paychannel and just change file name like
ramwithcard.bin , ramwithcard1.bin , ramwithcard2.bin , ramwithcard3.bin
now in C:\program files\openocd-r717\bin u should have 4 32mb bin files
now load these into hex editor and u want to search for your bk, ird and ird reversed
now sk is in the dumps
but this is as far as im going to spoonfeed
now research up on the sk data block / sk format .etc
and u will find it in the dumps
then all u need to do is stick it in a cam with camid and it should pair up with ur card
dont bother asking any questions regarding sk like: how does it look? , what address is it, .etc
as i wont reply
if u do ur research u will know how it looks .etc
i hope this gets some people intrested in cable again
Thanks to: The_coder, Mr0, Trojan, Chef1 for pointing me in right direction
first u need a usb jtag
i used this 1
Code:
You don't have permission to view the code content. Log in or register now.
and it would be helpfull if u install a 2x10 pin header
Code:
You don't have permission to view the code content. Log in or register now.
ok once u got the pinheader installed and have the usb jtag
u need to download the following drivers
Code:
You don't have permission to view the code content. Log in or register now.
also u will need hexworkshop or anyother hex file editor u like
and u will need openocd r717 that i have attached to this thread.
once drivers are installed
put the openocd folder into C:\program files
plug jtag into box and pc
power on the box WITH card inserted and on Stream
once box is powered up go to a pay channel
open up a command window type the following command:
Code:
You don't have permission to view the code content. Log in or register now.
now u need to enter this command:
Code:
You don't have permission to view the code content. Log in or register now.
now if everything is working u should get the following
Code:
You don't have permission to view the code content. Log in or register now.
and the box would have rebooted and stuck on pl30 or similar
now u need to use putty (included in openocd-r717 folder)
choose telnet and enter the following:
Code:
You don't have permission to view the code content. Log in or register now.
it should say the following in putty:
Open On-Chip Debugger
>
now u type the following command
Code:
You don't have permission to view the code content. Log in or register now.
now it will start dumping the ram should take around 20 / 30mins
once its dumped the ram
u need to close putty and command window
unplug box take scart out and unplug usb cable from pc
then repeat the steps 3 times remember same paychannel and just change file name like
ramwithcard.bin , ramwithcard1.bin , ramwithcard2.bin , ramwithcard3.bin
now in C:\program files\openocd-r717\bin u should have 4 32mb bin files
now load these into hex editor and u want to search for your bk, ird and ird reversed
now sk is in the dumps
but this is as far as im going to spoonfeed
now research up on the sk data block / sk format .etc
and u will find it in the dumps
then all u need to do is stick it in a cam with camid and it should pair up with ur card
dont bother asking any questions regarding sk like: how does it look? , what address is it, .etc
as i wont reply
if u do ur research u will know how it looks .etc
i hope this gets some people intrested in cable again
Thanks to: The_coder, Mr0, Trojan, Chef1 for pointing me in right direction
Attachments
Last edited: