just made big boo boo with putting sigma on 200 modem can anyone help me please i pressed y instead of 0 on line 8, can it be rectified.
1:Hook it all up, serial connection, ethernet ( set ip to 192.168.100.10, gateway to 192.168.100.1) and start the terminal emulator and the tftp server with the ambit200-sigma.bin in the server directory. Go to Serial port setup in the terminal and set the baud rate to 115200.
2:Start the modem and stop the boot by typing "p" (Enter '1', '2', or 'p' within 2 seconds or take default...)
3:Hit enter five times, you should see the boot menu now. - Board IP Address [192.168.100.1]:
Board IP Mask [255.255.255.0]:
Board IP Gateway [0.0.0.0]:
Board MAC Address [00:10:18:ff:ff:ff]:
Internal/External phy? (i/e)
4:Type "d" then hit enter (Enter sector number
5:Hit enter (Board TFTP Server IP Address [192.168.100.10]
6:Type "ambit200-sigma.bin" then hit enter (TFTP filename
7:Type "y" then hit enter (Image does not have standard header. Do you wish to store it? [n] Y
8:Type "0" then hit enter (Enter sector to start store: 0)
9:Type "n" then hit enter (Store parameters to flash ? [n] n)
Done. Now you have to do is a hard reboot/unplug the power for a few seconds.
--------------------------------------------------------------------------------------------------
this is what it says when i go into hyperterminal.
--------------------------------------------------------------------------------
i dont get the chance to press 'p' anymore because sigma is half installed
TCNiSO AMBIT 200 BOOT CPU = BCM3348A1
Ebi Initialized: 000002020000001C
Sdram Initialized: [ OK ]
CPU instruction cache size: 2000
CPU instruction cache line size: 0010
CPU data cache size: 2000
CPU data cache line size: 0010
Sdram access: [ OK ]
TCNiSO Compressed bootloader detected
Compressed bootloader size: 0062DA
Compressed Image location: 81F80000
Decompression Status: 00000000
Dcompressed Bootloader size: 00011005
BSS Initialized:
TMP Stack initialized: [ OK ]
Perm Stack initialized: [ OK ]
MemSize: ......................... 8M
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
TCNiSO SIGMA Bootloader v2.6
Build date: May 9 2005
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
Location: 0xBFC10000
Signature: 3348
Control: 0000
Major Rev: 0002
Minor Rev: 0001
Build Time: 2005/7/1 06:33:36 Z
File Length: 979059 bytes
Load Address: 80500000
Filename: sigma-x-1.06.rc4.beta.bin_decompressor.bin
Bypassing CRC Verifiction on Image 1...
Loading Image 1...
Executing Image 1...
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
TCNiSO FirmwareDecompressor v2.0.3
Detected Compressed Firmware..... Decompressing...
Target Address: 0x80010000
...................
Decompressed length: 4981401
3348
TCNiSO SIGMA-X Version 1.06 RC4
usrRoot:usrNetInit: complete!
SIGMA-X Version 1.06 RC4 BET
FlashDeviceDriver:etectFlash: ERROR - Failed to detect flash type (not CFI-co
mpliant)!
FlashDeviceDriver::FlashDriverInit: ERROR - Failed to autodetect flash device!
SIGMA config space found...
Hello... and welcome to the wonderful world of SIGMA-X!!
CmTargetLowLevelInit: Loading Flash/ProgramStore/NonVol drivers...
FlashDeviceDriver:etectFlash: ERROR - Failed to detect flash type (not CFI-co
mpliant)!
FlashDeviceDriver::FlashDriverInit: ERROR - Failed to autodetect flash device!
CmTargetLowLevelInit: Creating singletons for ProgramStore/BootloaderStore/NonV
ol devices...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::NonVolDriverMaxSizeBytes: ERROR - Failed to query flash reg
ion info!
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::NonVolDriverMaxSizeBytes: ERROR - Failed to query flash reg
ion info!
Reading Dynamic settings from non-vol...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::ReadTrueSegmentSizeBytes: ERROR - Failed to open the flash
driver!
NonVolDeviceDriver::NonVolDriverRead: ERROR - Failed to query the segment size
(returned 0 bytes)! There is no valid data to read.
0x00000154 ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::ReadImpl: (N
onVol Device) ERROR - Failed to read the length from the settings data!
0x0000015e ['tStartup' id=0x804bac70] BcmNon
l Device) ERROR - Failed to read the buffer from the device! Resetting the enti
re section to defaults.
0x00000172 ['tStartup' id=0x804bac70] BcmSnmpNonVolSettings::ResetDefaults: (SN
MP NonVol Settings) WARNING - Resetting Dynamic Settings!
*
*
* Failed to read non-vol settings from the device!
*
*
Reading Permanent settings from non-vol...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::ReadTrueSegmentSizeBytes: ERROR - Failed to open the
driver!
NonVolDeviceDriver::NonVolDriverRead: ERROR - Failed to query the segment size
(returned 0 bytes)! There is no valid data to read.
0x000001a4 ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::ReadImpl: (N
onVol Device) ERROR - Failed to read the length from the settings data!
0x000001ae ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::Read: (NonVo
l Device) ERROR - Failed to read the buffer from the device! Resetting the enti
re section to defaults.
0x000001c2 ['tStartup' id=0x804bac70] BcmHalIfNonVolSettings::ResetDefaults: (H
alIf NonVol Settings) WARNING - Resetting Permanent Settings to defaults! MAC a
ddresses and other settings are now invalid!
0x000001d6 ['tStartup' id=0x804bac70] BcmCmBpiNonVolSettings::ResetDefaults: (C
M BPI NonVol Settings) WARNING - Permanent settings (BPI Keys and other unique v
alues) are being reset to their default values!
0x000001ea ['tStartup' id=0x804bac70] BcmSnmpNonVolSettings::ResetDefaults: (SN
MP NonVol Settings) WARNING - Resetting all Permanent Settings! The serial numb
er and other Sys Info items are probably invalid!
0x000001f4 ['tStartup' id=0x804bac70] BcmDocsisCmDownstreamCalibrationNonVolSett
ings::ResetDefaults: (DOCSIS CM Downstream Calibration NonVol Settings) WARNING
- Resetting Permanent Settings to defaults! The downstream calibration table w
ill reset to default values!
0x00000212 ['tStartup' id=0x804bac70] BcmDocsisCmUps
treamCalibrationNonVolSettings::ResetDefaults: (DOCSIS CM Upstream Calibration
NonVol Settings) WARNING - Resetting Permanent Settings to defaults! The upstre
am calibration tables will be configured for the default Amplifier!
*
*
* Failed to
read non-vol settings from the device!
*
WatchDOG: DISABLED
DISABLED
0x0000023a ['tStartup' id=0x804bac70] BcmVxRemoteTerminalConsoleThread::BcmVxRem
oteTerminalConsoleThread: (ConsoleThread) ERROR - iosDrvInstall failed! Couldn
't install the Telnet IO driver!
CatTel: Console Task Started
Calling Vendor PreDriverInitialization...
CatTel: Telnet socket bind() error-PreDriverInitialization: Tuner 0 Amp 4
tunerInit()
Attaching network interface lo0... done.
NOTE: Driver initialization was skipped! Th
d data. You can change NonVol Setting, but that's about it...
SIGMA-X Copyright (c) 2005 TCNiSO Corporation
4:30PM 2005
4:30PM
TCNiSOSX 1.06- vxWorks PID=0x3348DOCSIS 1.0 BPI/BPI+ (no IPSEC) (no EMTA)SNMPv3
(WindRiverWindManage 9.3)
SB5100 DOCSIS 1.0 Cable Modem Application starting!
I hope I didn't brain my damage.
SIGMA-X Version 1.06 RC4 BETA1
SIGMA: 82744 bytes.
Bloat: 00104936 bytes.
Safe: 4980 bytes.
Wacked: socket-21632 bytes.
Foot: 0004901528 bytes.
Coma: 6956 bytes.
TS: ! Sleeping then retrying
20140 bytes.
SIGMA httpd: 4312 bytes.
SIGMA html: 52888 bytes.
Beginning Cable Modem operation...
Type 'help' or '?' for a list of commands...
WARNING - No DOCSIS Control thread provided. DOCSIS state machine can't run!
CM> CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
thank you for any responce
1:Hook it all up, serial connection, ethernet ( set ip to 192.168.100.10, gateway to 192.168.100.1) and start the terminal emulator and the tftp server with the ambit200-sigma.bin in the server directory. Go to Serial port setup in the terminal and set the baud rate to 115200.
2:Start the modem and stop the boot by typing "p" (Enter '1', '2', or 'p' within 2 seconds or take default...)
3:Hit enter five times, you should see the boot menu now. - Board IP Address [192.168.100.1]:
Board IP Mask [255.255.255.0]:
Board IP Gateway [0.0.0.0]:
Board MAC Address [00:10:18:ff:ff:ff]:
Internal/External phy? (i/e)
4:Type "d" then hit enter (Enter sector number
5:Hit enter (Board TFTP Server IP Address [192.168.100.10]
6:Type "ambit200-sigma.bin" then hit enter (TFTP filename
7:Type "y" then hit enter (Image does not have standard header. Do you wish to store it? [n] Y
8:Type "0" then hit enter (Enter sector to start store: 0)
9:Type "n" then hit enter (Store parameters to flash ? [n] n)
Done. Now you have to do is a hard reboot/unplug the power for a few seconds.
--------------------------------------------------------------------------------------------------
this is what it says when i go into hyperterminal.
--------------------------------------------------------------------------------
i dont get the chance to press 'p' anymore because sigma is half installed
TCNiSO AMBIT 200 BOOT CPU = BCM3348A1
Ebi Initialized: 000002020000001C
Sdram Initialized: [ OK ]
CPU instruction cache size: 2000
CPU instruction cache line size: 0010
CPU data cache size: 2000
CPU data cache line size: 0010
Sdram access: [ OK ]
TCNiSO Compressed bootloader detected
Compressed bootloader size: 0062DA
Compressed Image location: 81F80000
Decompression Status: 00000000
Dcompressed Bootloader size: 00011005
BSS Initialized:
TMP Stack initialized: [ OK ]
Perm Stack initialized: [ OK ]
MemSize: ......................... 8M
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
TCNiSO SIGMA Bootloader v2.6
Build date: May 9 2005
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
Location: 0xBFC10000
Signature: 3348
Control: 0000
Major Rev: 0002
Minor Rev: 0001
Build Time: 2005/7/1 06:33:36 Z
File Length: 979059 bytes
Load Address: 80500000
Filename: sigma-x-1.06.rc4.beta.bin_decompressor.bin
Bypassing CRC Verifiction on Image 1...
Loading Image 1...
Executing Image 1...
flashDetect: ERROR: Flash programming FAILED: 3
flashGetBase: ERROR: Flash programming FAILED: 3
TCNiSO FirmwareDecompressor v2.0.3
Detected Compressed Firmware..... Decompressing...
Target Address: 0x80010000
...................
Decompressed length: 4981401
3348
TCNiSO SIGMA-X Version 1.06 RC4
usrRoot:usrNetInit: complete!
SIGMA-X Version 1.06 RC4 BET
FlashDeviceDriver:
etectFlash: ERROR - Failed to detect flash type (not CFI-co mpliant)!
FlashDeviceDriver::FlashDriverInit: ERROR - Failed to autodetect flash device!
SIGMA config space found...
Hello... and welcome to the wonderful world of SIGMA-X!!
CmTargetLowLevelInit: Loading Flash/ProgramStore/NonVol drivers...
FlashDeviceDriver:
etectFlash: ERROR - Failed to detect flash type (not CFI-co mpliant)!
FlashDeviceDriver::FlashDriverInit: ERROR - Failed to autodetect flash device!
CmTargetLowLevelInit: Creating singletons for ProgramStore/BootloaderStore/NonV
ol devices...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::NonVolDriverMaxSizeBytes: ERROR - Failed to query flash reg
ion info!
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::NonVolDriverMaxSizeBytes: ERROR - Failed to query flash reg
ion info!
Reading Dynamic settings from non-vol...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::ReadTrueSegmentSizeBytes: ERROR - Failed to open the flash
driver!
NonVolDeviceDriver::NonVolDriverRead: ERROR - Failed to query the segment size
(returned 0 bytes)! There is no valid data to read.
0x00000154 ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::ReadImpl: (N
onVol Device) ERROR - Failed to read the length from the settings data!
0x0000015e ['tStartup' id=0x804bac70] BcmNon
l Device) ERROR - Failed to read the buffer from the device! Resetting the enti
re section to defaults.
0x00000172 ['tStartup' id=0x804bac70] BcmSnmpNonVolSettings::ResetDefaults: (SN
MP NonVol Settings) WARNING - Resetting Dynamic Settings!
*
*
* Failed to read non-vol settings from the device!
*
*
Reading Permanent settings from non-vol...
FlashDeviceDriver::FlashDriverGetRegionInfo: WARNING - Invalid region specified
; returning NULL
NonVolDeviceDriver::ReadTrueSegmentSizeBytes: ERROR - Failed to open the
driver!
NonVolDeviceDriver::NonVolDriverRead: ERROR - Failed to query the segment size
(returned 0 bytes)! There is no valid data to read.
0x000001a4 ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::ReadImpl: (N
onVol Device) ERROR - Failed to read the length from the settings data!
0x000001ae ['tStartup' id=0x804bac70] BcmNonVolDeviceDriverBridge::Read: (NonVo
l Device) ERROR - Failed to read the buffer from the device! Resetting the enti
re section to defaults.
0x000001c2 ['tStartup' id=0x804bac70] BcmHalIfNonVolSettings::ResetDefaults: (H
alIf NonVol Settings) WARNING - Resetting Permanent Settings to defaults! MAC a
ddresses and other settings are now invalid!
0x000001d6 ['tStartup' id=0x804bac70] BcmCmBpiNonVolSettings::ResetDefaults: (C
M BPI NonVol Settings) WARNING - Permanent settings (BPI Keys and other unique v
alues) are being reset to their default values!
0x000001ea ['tStartup' id=0x804bac70] BcmSnmpNonVolSettings::ResetDefaults: (SN
MP NonVol Settings) WARNING - Resetting all Permanent Settings! The serial numb
er and other Sys Info items are probably invalid!
0x000001f4 ['tStartup' id=0x804bac70] BcmDocsisCmDownstreamCalibrationNonVolSett
ings::ResetDefaults: (DOCSIS CM Downstream Calibration NonVol Settings) WARNING
- Resetting Permanent Settings to defaults! The downstream calibration table w
ill reset to default values!
0x00000212 ['tStartup' id=0x804bac70] BcmDocsisCmUps
treamCalibrationNonVolSettings::ResetDefaults: (DOCSIS CM Upstream Calibration
NonVol Settings) WARNING - Resetting Permanent Settings to defaults! The upstre
am calibration tables will be configured for the default Amplifier!
*
*
* Failed to
read non-vol settings from the device!
*
WatchDOG: DISABLED
DISABLED
0x0000023a ['tStartup' id=0x804bac70] BcmVxRemoteTerminalConsoleThread::BcmVxRem
oteTerminalConsoleThread: (ConsoleThread) ERROR - iosDrvInstall failed! Couldn
't install the Telnet IO driver!
CatTel: Console Task Started
Calling Vendor PreDriverInitialization...
CatTel: Telnet socket bind() error-PreDriverInitialization: Tuner 0 Amp 4
tunerInit()
Attaching network interface lo0... done.
NOTE: Driver initialization was skipped! Th
d data. You can change NonVol Setting, but that's about it...
SIGMA-X Copyright (c) 2005 TCNiSO Corporation
4:30PM 2005
4:30PM
TCNiSOSX 1.06- vxWorks PID=0x3348DOCSIS 1.0 BPI/BPI+ (no IPSEC) (no EMTA)SNMPv3
(WindRiverWindManage 9.3)
SB5100 DOCSIS 1.0 Cable Modem Application starting!
I hope I didn't brain my damage.
SIGMA-X Version 1.06 RC4 BETA1
SIGMA: 82744 bytes.
Bloat: 00104936 bytes.
Safe: 4980 bytes.
Wacked: socket-21632 bytes.
Foot: 0004901528 bytes.
Coma: 6956 bytes.
TS: ! Sleeping then retrying
20140 bytes.
SIGMA httpd: 4312 bytes.
SIGMA html: 52888 bytes.
Beginning Cable Modem operation...
Type 'help' or '?' for a list of commands...
WARNING - No DOCSIS Control thread provided. DOCSIS state machine can't run!
CM> CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then
CatTel: Telnet socket bind() error-0049 socket-0006! Sleeping then retrying
thank you for any responce
Last edited:
