service problem

[steady]

when i am flashing images on to the box when i go to service then service scan instead of getting the normall settings scan for services
bouqet
cable provider
fast scan
manuel scan then start scan at the bottom
instead it reads like this
scan for services
bouqet
diseqc
zanternal error
uncommited
sattelite
hence it wont let me scan any help would be much appreciated

 

[Nullsleep]

that sounds like a bad flash, but i could be wrong, what image is on the box? have you tried another image?

 

[cryptyk]

that deffo needs reflashing you wont get anything from a scan

 

[acercam]

when i am flashing images on to the box when i go to service then service scan instead of getting the normall settings scan for services
bouqet
cable provider
fast scan
manuel scan then start scan at the bottom
instead it reads like this
scan for services
bouqet
diseqc
zanternal error
uncommited
sattelite
hence it wont let me scan any help would be much appreciated

Sounds like it's been flashed for satellite and not cable mate.

regards acercam

 

[thebigman]

What image are you trying to use? it could be a tuner fault if the cable tuner is not detected on boot up the image will default to sat. Try a reflash first, if it still reverts to sat you've prob got a hardware fault, in that case post a boot log.

thebigman

 

[steady]

What image are you trying to use? it could be a tuner fault if the cable tuner is not detected on boot up the image will default to sat. Try a reflash first, if it still reverts to sat you've prob got a hardware fault, in that case post a boot log.

thebigman

sounds like you are right i have tried severall images but each go to sattellite scan as if it isnt reading anything will try and find how to get a bootlog cheers

 

[Fergalsworld]

sounds like you are right i have tried severall images but each go to sattellite scan as if it isnt reading anything will try and find how to get a bootlog cheers

Here you go
http://www.digitalworldz.co.uk/forums/index.php?resources/739/

 

[steady]

here is my bootlog i think much appriciation of any help pointing me to the fault



debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS
debug: BMon V1.2 mID 03
debug: feID 00 enxID 03
debug: fpID 52 dsID http://Hallenberg.com
debug: HWrev 61 FPrev 0.23
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032
debug: Got Block #0036
debug: Got Block #0040


will verify ELF image, start= 0x800000, size= 149536
verify sig: 262
Branching to 0x40000


U-Boot 1.1.4 (Tuxbox) (Aug 30 2006 - 17:05:40)

CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.2
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: . | / - \ | / - \ . | / - \ | / - \ | . / . - \ | / . . - \ | / . - \ | / . .  done.

env: can't set "baudrate"
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET

Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 1  0
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 669543 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 669479 Bytes = 653.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK

------ Systeminformations ------
Selected networkdevice: VIA Rhine II Fast Ethernet Adapter - Packet Scheduler Miniport (1)
IP-address of the networkdevice: 169.254.10.93
IP-address which the dbox gets: 169.254.10.202
Operatingsystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600)
------ Powered by http://www.dboxservice-hallenberg.de ------

 

[mastichick]

What image are you trying to use? it could be a tuner fault if the cable tuner is not detected on boot up the image will default to sat. Try a reflash first, if it still reverts to sat you've prob got a hardware fault, in that case post a boot log.

thebigman

Hi

I think thebigman is spot on, if tuner is faulty it will default to sat as Ive had that with a couple of boxes that had tuner faults.

Regards

 

[steady]

tried a reflash still going to sattellite posted what i think is a bootlog any advice out there

 

[bigears]

is this a new box m8 or been working on cable previously ? i.e is does it have a cable tuner or is it a sat tuner ?

threaded connector of f type.

I know this might be obvious to some but it's sometimes the obvious that catch's you out.