No Net I.D.

zero

Inactive User
Joined
Jun 11, 2005
Messages
21
Reaction score
0
HI,
Di4001 has no net I.D. Just ***** tried libby no good. Box was working fine.
Thanks in advance for any help.:Cheers:
 
There's lots on this .... try changing the CIM module, and/or swapping the two tuner modules- front for back.
 
please display some pictures of page 6 and 10 of the eng menu while the box is in stream.

page 6 refers to the reception of channels downstream tuner
page 10 refers to the reception of data i.e netid ect

if both page 6 and 10 indicate no lock then your cim is not functioning correctly.

page 6 tuner requires 29db+ to work a1
page 10 tuner requires 19db+ to achieve updates and 16db+ to acquire a netid.

if you are unsure then post the pictures of the pages for guidance
 
Nothin to do with cim or anythin else.
Ive done 4 in a row that just came out the stream and they all set themselfs to ***** on net id when i put the mosc in.
one of my m8s has the same problem.
 
gazzas said:
Nothin to do with cim or anythin else.
Ive done 4 in a row that just came out the stream and they all set themselfs to ***** on net id when i put the mosc in.
one of my m8s has the same problem.
oh well doubt it was anything you did wrong then !!!! after all 4 in a row must just be bad luck.
 
m8 brought another 2 today and same happend again.
 
Ps ive tried changin the cim on the first 4 and ran the voltmeter over like the tut says.
Dont a few of these and only ever had 1 or 2 do it but sorted them.
 
Hi lads,Not sure how to display pictures of page 6 and 10 but this what they say:-
Page 6.
Chan Freq 0 .
Quam 064
MSPS Symbol 0.000
Tuner AGC 50%
IF AGC 50%
Pre RS 0.0e+00
Post RS 0.0e+00
Snr Esitmate dB
Lock Status unlocked

Page 10
Chan Freq 000.000
Baud rate 0.000
Tuner AGC 50%
IF AGC 50%
Pre RS 0.0e+00
Post RS not reported
SNR Estimate dB
Lock Staus unlocked
Synchronization 0
Acqistion 0

Hope this helps
 
zero said:
Hi lads,Not sure how to display pictures of page 6 and 10 but this what they say:-
Page 6.
Chan Freq 0 .
Quam 064
MSPS Symbol 0.000
Tuner AGC 50%
IF AGC 50%
Pre RS 0.0e+00
Post RS 0.0e+00
Snr Esitmate dB
Lock Status unlocked

Page 10
Chan Freq 000.000
Baud rate 0.000
Tuner AGC 50%
IF AGC 50%
Pre RS 0.0e+00
Post RS not reported
SNR Estimate dB
Lock Staus unlocked
Synchronization 0
Acqistion 0

Hope this helps

this shows a simultaneous failure in both tuners - this is extremely unlikely therefore you must try a known working cim module.
of course this could also be a failure in the 33v feed to the tuners (look at the stuck in tune tut to establish the presence of the correct voltages)
 
Last edited:
ive had same problem dont think its the tuner as agc shows high enough take out red jumper on mainboard and battery leave for 5 min they replace insert card attach cable power on keeping up and down pressed in simultaneously box should update and find net id
 
have u tried eraseing the sram
this is like a reset of the box to factory settings
should show 099999
try it let me know
 
all langley boxes show ***** as a factory setting unlike docsis which will return to 09999 as a factory setting.

i was sort of wondering if you had the same problem without the mosc in the box???
 
Hi lads,

I'll try give battery a go.
To the erase sram, did that (password was erased) but did not change net ID.
Mosc question, Yes same problem in or out.
 
Back
Top