hi all
Managed to get a null modem cable here is the bootlog any help is appreciated thanks debug: Got Block #0040
will verify ELF image, start= 0x800000, size= 152952
verify sig: 263
Branching to 0x40000
U-Boot 1.1.2 (TuxBox) (May 23 2004 - 21:44:01)
CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache
Board: DBOX2, Sagem, BMon V1.3
Watchdog enabled
I2C: ready
DRAM: 32 MB
FLASH: 8 MB
Scanning JFFS2 FS: ........ done.
FB: ready
LCD: ready
In: serial
Out: serial
Err: serial
Net: SCC ETHERNET
Options:
1: Console on null
2: Console on ttyS0
3: Console on framebuffer
Select option (1-3), other keys to stop autoboot: 0
...............................................................
Un-Protected 63 sectors
### FS (jffs2) loading 'vmlinuz' to 0x100000
### FS load complete: 631075 bytes loaded to 0x100000
## Booting image at 00100000 ...
Image Name: dbox2
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 631011 Bytes = 616.2 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.4.31-dbox2 (sportster@bar-wsl01) (gcc version 3.3.5) #25 Sa Jul
30 18:26:20 CEST 2005
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rw console=ttyS0
Decrementer Frequency = 247500000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x2580)
Console: colour dummy device 80x25
Calibrating delay loop... 65.74 BogoMIPS
Memory: 30864k available (1076k kernel code, 368k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (
[email protected])
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3e:0f:fa
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
Creating 5 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x00800000 : "root (JFFS2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cramfs: wrong magic
VFS: Mounted root (jffs2 filesystem).
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
Starting pid 11, console /dev/console: '/etc/init.d/rcS'ti-call b
Using /lib/modules/2.4.31-dbox2/misc/event.o
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/tuxbox.o
Using /lib/modules/2.4.31-dbox2/misc/dvb-core.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_i2c.o
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp.o
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_input.o
Using /lib/modules/2.4.31-dbox2/misc/avs.o
Oops: kernel access of bad area, sig: 11
NIP: C009FB20 XER: 00000000 LR: C389B514 SP: C1DC7E30 REGS: c1dc7d80 TRAP: 0300
Not tainted
MSR: 00009032 EE: 1 PR: 0 FP: 0 ME: 1 IR/DR: 11
DAR: 00000024, DSISR: C0000000
TASK = c1dc6000[23] 'insmod' Last syscall: 128
last math 00000000 last altivec 00000000
GPR00: C389B514 C1DC7E30 C1DC6000 C389D648 C389D626 00000007 C012A2EC 00000019
GPR08: 00000000 00000004 0000003F C009FB08 24008022 1007218C 00000000 00000000
GPR16: 00000000 00000000 00000000 00000000 00009032 1014BFCC C1D2A000 C1DC7EA0
GPR24: C1F0CCC0 00000003 C389F000 FFFFFFEA C0130000 00000007 00000000 00000000
Call backtrace:
C389C26C C389B514 C389C9D8 C0010694 C000257C 10148DA8 1001CFEC
1001E314 10003DBC 100039F8 0FEEF464 00000000
Segmentation fault
Using /lib/modules/2.4.31-dbox2/misc/saa7126.o
i2c-core.o: driver saa7126 registered.
i2c-core.o: client [saa7126] registered to adapter [PowerPC 8xx I2C adapter](pos
. 1).
Detected STB:
Vendor: Sagem
Model: D-BOX2
Using /lib/modules/2.4.31-dbox2/misc/cam.o
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
i2c-core.o: driver DBox2-CAM registered.
i2c-core.o: client [DBox2-CAM] registered to adapter [PowerPC 8xx I2C adapter](p
os. 2).
Using /lib/modules/2.4.31-dbox2/misc/dvb_i2c_bridge.o
Using /lib/modules/2.4.31-dbox2/misc/avia_napi.o
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
i2c-core.o: driver DVB I2C bridge registered.
i2c-core.o: client [DVB I2C bridge] registered to adapter [PowerPC 8xx I2C adapt
er](pos. 3).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
Using /lib/modules/2.4.31-dbox2/misc/cam_napi.o
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_napi.o
Using /lib/modules/2.4.31-dbox2/misc/avia_av_alt.o
route: SIOC[ADD|DEL]RT: Network is unreachable
avia_av: $Id: avia_av_core.c,v 1.89 2004/02/27 22:17:44 obi Exp $
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt.o
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... eNX
avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_ucode: loaded ucode v001A
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_fb.o
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
Using /lib/modules/2.4.31-dbox2/misc/lcd.o
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_lirc.o
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_oss.o
avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $
avia_gt_pcm_set_rate(44100)
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_v4l2.o
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
Using /lib/modules/2.4.31-dbox2/misc/at76c651.o
DVB: registering frontend 0:0 (Atmel AT76C651B with TUA6010XS)...
Using /lib/modules/2.4.31-dbox2/misc/ves1x93.o
Using /lib/modules/2.4.31-dbox2/misc/avia_av_napi.o
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_napi.o
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
Using /lib/modules/2.4.31-dbox2/misc/dvb2eth.o
Using /lib/modules/2.4.31-dbox2/misc/aviaEXT_alt.o
Using /lib/modules/2.4.31-dbox2/misc/avia_gt_proc.o
avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2003/09/25 12:24:00 Skars & Merandos
Exp $
avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension
options:
(demux reinit) enx_reset=1
(framer chan.) fc_reset=0
(clr avia reg) avia=1
(enx td trace) trace=0
(lock, unlock) spinlock=0
Schreiben ueber avia_gt.o
(delay) delay=10
Starting pid 83, console /dev/console: '/etc/init.d/start'
Please press Enter to activate this console. cdkVcInfo $Id: cdkVcInfo.c,v 1.0 20
02/09/26 20:48:26 alexW Exp $
Setting Date...
Thu Jan 1 01:00:00 CET 1970
Starting sectionsd...
$Id: sectionsd.cpp,v 1.184 2005/05/02 19:06:35 rasc Exp $
caching 168 hours
events are old 60min after their end time
Starting timerd...
Starting Camd..
warte auf evocamd (max. 5 Sekunden)
evocamd erfolgreich gestartet
Starting zapit...
$Id: zapit.cpp,v 1.371 2005/04/17 06:56:15 metallica Exp $
Couldn't open config file: /var/keys/newcamd-client.txt
============================================================
(compiled Oct 21 2005 21:11:30)
styled by TBT Team, Next Level version 1.01(dream-dbox2-Triple Dragon)
============================================================
/var/tuxbox/config/zapit/antiservices.xml: No such file or directory
[evocamd] Process id 192
/var/tuxbox/config/zapit/myservices.xml: No such file or directory
[camd] ca system id: 1722
Starting controld...
$Id: controld.cpp,v 1.117 2004/05/22 14:34:09 carjay Exp $
[controld] Boxtype detected: (3, Sagem D-BOX2)
Starting nhttpd...
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld] /dev/dbox/avs0: No such file or directory
[controld] setting VideoFormat to auto
[controld] /dev/dbox/avs0: No such file or directory
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core...Starting neutrino...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] Software update enabled
[neutrino] enable flash
[english.locale] missing entry: flashupdate.proxypassword_hint2
[english.locale] superfluous entry: fontsize.imageinfo_info
[english.locale] superfluous entry: fontsize.imageinfo_small
[english.locale] superfluous entry: imageinfo.creator
[english.locale] superfluous entry: imageinfo.date
[english.locale] superfluous entry: imageinfo.dokumentation
[english.locale] superfluous entry: imageinfo.forum
[english.locale] superfluous entry: imageinfo.head
[english.locale] superfluous entry: imageinfo.homepage
[english.locale] superfluous entry: imageinfo.image
[english.locale] superfluous entry: imageinfo.license
[english.locale] superfluous entry: imageinfo.version
[english.locale] superfluous entry: miscsettings.tuxtxt_cache
[english.locale] missing entry: movieplayer.bookmarkname_hint2
[english.locale] superfluous entry: servicemenu.imageinfo
[english.locale] superfluous entry: servicemenu.restart
[english.locale] superfluous entry: servicemenu.restart_failed
[english.locale] superfluous entry: servicemenu.restart_hint
[english.locale] superfluous entry: servicemenu.restart_refused_recording
[english.locale] superfluous entry: shutdown.recoding_query
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
/dev/input/event1: No such file or directory
[neutrino] menue setup
[controld] setting VideoFormat to auto
[controld] /dev/dbox/avs0: No such file or directory
loading locales: scandir: No such file or directory
[neutrino] registering as event client
[controld] setting VideoFormat to auto
[controld] /dev/dbox/avs0: No such file or directory
[neutrino] initialized everything
zap failed!
[sectionsd] getUTC: read: Connection timed out