Skybox F3 Ftp Tool

faisalpandu

VIP Member
VIP Member
Joined
Jan 8, 2007
Messages
1,334
Reaction score
28
Hi

I am trying to ftp into the skybox f3 using the STBHD LAN tool.

I can do it fine with Openbox but not with a Skybox. Is this supported. I have setup static ip enterted in tool and enterted 0000 as password but wont connect.

Any Ideas
 
those boxes have their own version of the lan tool,which uses a different port than the old version for s10.

This is the Lan Tool for SKYBOX F3/M3/F4, OPENBOX X3/Q3/X4/Q4 Models
 

Attachments

  • F3X3LanTool.rar
    879.8 KB · Views: 298
Last edited by a moderator:
Worked perfect mate

Does anybdoy know how to change the default password to FTP in.
 
change the receiver password,but others in the house might get mad.
Should be under parental controls.Don't forget the password or you are screwed.
 
the old s10 lan manager had a \config folder with a config.ini file.
When this version came out there was no config.ini file with it so I copied the one from the s10 folder.
Since I had no f3 to test it on,it failed with the s10 but updated the config.ini with the new port it uses vs. the old version.If your find a config.ini in that folder it will have the latest password you used to get in just in case you forget.It uses port 0x1003 and the old program uses 0x1000.Why one program won't work with the other type receiver.You can open the config.ini with any text editor to read it.
 
those boxes have their own version of the lan tool,which uses a different port than the old version for s10.

This is the Lan Tool for SKYBOX F3/M3/F4, OPENBOX X3/Q3/X4/Q4 Models


Hi slugh

thxs for the input, having that said we can only access CA modules available in firmware, i noticed that the mg_cfg is missing in all firmwares

so we can all agree its not a mgcamd emu but a simple newcamd5.25 protocoll working...

any info on how i could compile the module for mgcamd with the real AU , EMM routines etc..

Thxks anyways.

As we all know ALI chips cannot run full linux platform or even enigma2 platforms.
 
this lan tool is crap how in hell do you connect the pc and reciever together in truth when buying such items why should you have to all crap they should work from the off. Its a linux based satellite reciever why switch of the lan it dont make sense cause not everyone is technically minded, why cant it be simple and why is the rj45 port not working?

but thank you guys for your help
 
it isn't real linux and the lan manager saves wear and tear on the usb port if you keep yanking the usb device all the time.FTP tool is actually a misnomer because it has nothing to do with ftp.The lan manager uses tcp/udp for file transfer.A real ftp program won't work with the receiver.
 
This tool would be great, but it crashes all the time on my Windows 7 Ultimate 32-bit PC. I can login okay to the M3 but immediately the tool crashes:

Problem Event Name: APPCRASH
Application Name: X3_LAN_TOOL.EXE
Application Version: 1.0.0.1
Application Timestamp: 4f5821df
Fault Module Name: X3_LAN_TOOL.EXE
Fault Module Version: 1.0.0.1
Fault Module Timestamp: 4f5821df
Exception Code: c0000005
Exception Offset: 0000b6ba
OS Version: 6.1.7601.2.1.0.256.1
Locale ID: 2057
Additional Information 1: 0a9e
Additional Information 2: 0a9e372d3b4ad19135b953a78882e789
Additional Information 3: 0a9e
Additional Information 4: 0a9e372d3b4ad19135b953a78882e789

I tried adding it to exceptions in my anti-virus and Windows firewall - no luck. I also tried running it as administrator and in XP compatibility mode, without success. It did work just one time today, but all other times it crashed. Any suggestions?
 
Update: The tool also crashes on my XP laptop after connecting to my M3, so I guess it must be a problem in the hardware of the box or the latest firmware. Ethernet cable is fine - tried two and YouTube plays well with both.

I've done a lot of googling and no one else is reporting this problem. If anyone is successfully using the tool with an M3 and the latest firmware dated 27/3/2013, please speak up.
 
Has any one actually figured how AU through F3, i have the correct mgcamd settings but no way to update through though this box
 
i am trying to get my cam file from the box so i can update any help would be appreciated!
 
Back
Top