bod script help

linzi

Inactive User
Joined
Jun 16, 2005
Messages
723
Reaction score
3
could anyone help me im tearing my hair out cant get this working its saying unable to identify provider exiting in win explorer
 
could anyone help me im tearing my hair out cant get this working its saying unable to identify provider exiting in win explorer

Try and read your card via your phoenix compatible programmer in nagra and see what it says. It shounds like the card may be soft looped. You may find when you try and read it in nagra it says "provider id 00" or something like that.
 
your card needs to be glitched..... you need to unlock the card with glitcher something like ubomb or t911 or nexus gliticher to unlock the card to get the info off..: multi : : multi : : multi : : multi :
 
erm that what im using a t911 lol other cards seem to go fine but not the bod
 
You need to flash your unlooper with newd11x (my guess is you're trying to use newd11)

edcase
 
yes i think i am but i cant remember how to do it all and can t find out
 
dont no if ive flashed it properly but now im gettin
________________Setting up WinExplorer_________________

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script


Script Error on Line 396
Sc.GetByte: Requested Byte Exceeds Last Read Request
 
flash unlooper with the new d11X flash. drop winexplorer ini file into winexplorer directory and run the script
 
dont no if ive flashed it properly but now im gettin
________________Setting up WinExplorer_________________

Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script


Script Error on Line 396
Sc.GetByte: Requested Byte Exceeds Last Read Request

Make sure you are running WinExplorer in Win98 compatibility mode....
 
just recieved my t911 today , installed the new d11 flash as posted above by jumpinjo , and dropped the ini file into winexp , also made sure that the compatibility mode was set to win 98 as suggested by timbo , so far so gd ,wen i load the script into win exp thats ok , then put the card in t911 no prob , then run script it comes up as the vcc 30 and when it doin the card , the screen in win exp has loads of ------------ while running and not ++++++++ ,

then comes up with
Sc.Read: Timeout Reading Data From Card - 2 Bytes Requested, 0 Bytes Read, Continuing Script


Script Error on Line 171
Sc.GetByte: Requested Byte Exceeds Last Read Request

sometimes it diff line numbers

have tried turning the pot to get the vcc lower as i noticed in another post that it should be around the 20 mark , but everytime i run the script the vcc is still 30

any suggestions or is there anyone local to northants who could help out
 
Last edited:
if you are getting --------- then your pot needs ajusting until you get +++---++-- and the vcc 20 -30 mark.

tmc
 
have tried adjusting the pot / trimmer and have took it right round from 12 o clock position to 12 o clock postion , but wen i run the script it still shows as vcc 30 as in pic
 
first vcc is always 30 you need to look at the second one. Also if you set the pot to about 2k then you will be close to what you need for rom 11.

tmc
 
Also check the dip switch is set to 2 and 5 and the switch is towards the dip switch and not the power socket.
 
when it checks the 2nd time it is coming up with something like fffffb or something like that

i take it that the pot is the blue bit next to the card slot in this pic
 
yes m8 the pot setting is out ajust it slowly while running

tmc
 
been trying to adjust the trimmer/pot , been right the way round and bk again , still only getting ---------- wen running script , is there a easy way of finding where the 20-30 mark is , as have been trying since this morn and still got nowhere
 
Back
Top