OCD commander will not work!!!

Nikko

Inactive User
Joined
Jun 10, 2007
Messages
130
Reaction score
0
Location
Manchester
Hi there all

Could anyone help here

Here it goes.......

I have jtaged 3 boxes (2100c & 4000s) no problem used bke2.2 with MOT running in background, obtaining the bk and ird from all three boxes. Next i do my fun card, again no problems all fine. But as soon as i use OCD knowing my soldering is correct as moments before i have used bke i get an error message not yet intialized or with the 2005 version i get internal error 43 as well just before not yet intialized.

-I have tried using in all compatibility modes
-I have tried all versions of OCD
-I have tried on 2 PCs running XP
-ECP is set as parrallel port

I have read a post where someone had the same issue but i have tried what they did with no sucess

Am i not installing something? or does OCD like certain solder point on the jtag?

The reason i need to do this is to get movies PIN working.

Please help its annoying
 
Hi there all

Could anyone help here

Here it goes.......

I have jtaged 3 boxes (2100c & 4000s) no problem used bke2.2 with MOT running in background, obtaining the bk and ird from all three boxes. Next i do my fun card, again no problems all fine. But as soon as i use OCD knowing my soldering is correct as moments before i have used bke i get an error message not yet intialized or with the 2005 version i get internal error 43 as well just before not yet intialized.

-I have tried using in all compatibility modes
-I have tried all versions of OCD
-I have tried on 2 PCs running XP
-ECP is set as parrallel port

I have read a post where someone had the same issue but i have tried what they did with no sucess

Am i not installing something? or does OCD like certain solder point on the jtag?

The reason i need to do this is to get movies PIN working.

Please help its annoying



Just read last part of post - dont worry about diag screen and try using this - open ocd and select mac then run the 4000 mac this will run for half hour then stop boot box up and wait but dont take off the red jumper
 
Just read last part of post - dont worry about diag screen and try using this - open ocd and select mac then run the 4000 mac this will run for half hour then stop boot box up and wait but dont take off the red jumper

First thanx for the help.

But mate the attach has lost me as to what u mean i should do, i have both the files in the rar, as in the macro files but the bytes if im getting these errors and ocd is not working how do i use them to resolve the problem
 
had the same problems myself,,just used another pc and it was fine
 
yes im booting the 2100c in diag mode by holding the down key when it hits ld 20 then it goes to ld 40 then green light on power button with no display on channel number screen. But it still dont work

Any other suggestions mate thanx so far
 
Yes....... solder in the JTAG then check you can run BKE and it connects and gives IRD+BK.
Then start OCD and see if it connects.Most recent common problems have been the version of OCD. Older versions work, the latest one doesn't...
 
Yes....... solder in the JTAG then check you can run BKE and it connects and gives IRD+BK.
Then start OCD and see if it connects.Most recent common problems have been the version of OCD. Older versions work, the latest one doesn't...

if you read above i have already done what u have stated............thanx for your advise anyway
 
where did you buy your jtag m8 ???

Well i have two jtags to be honest....

But i dont understand the question to be honest.

I have 1 from TMC
I have one which is done by the ntlhell guy who is giving it all up from where i live which is a lot better quality to be honest. but they both work as i have tried them both in bke2.2
 
Last edited:
i might fresh install my laptop and try both jtags??

What u think guys?

Cheers
 
hi m8 what pinout on the sammy r u using for the grounds
 
i might fresh install my laptop and try both jtags??

What u think guys?

Cheers


either that or try them on a 3rd pc m8, {there is another alternative if you use flash programer to do your reading and writeing , "its less tempromental than ocd"
 
try pin 20 i had lots of problems with ocd and marco until i use pin 20

Right i will try what u have advised tomoz as i need to pop out now...

I will post back when i have cracked it as im sure other people have this problem

cheers gentlex as ur posts have helped me alot
 
make sure your port is set to epp in bios settings have mac mot running boot box up if your loading a macro dont put stb in eng menu just power it up and open ocd 2005 and should work it should not matter wich pin to use for ground aslong as its either 4 6 8 10 12 14 16 18 20 unless 1 of them is damaged you can also attach grnd to stb its self should work m8
 
Right ive sorted it now.....

-used ocd 2004
-used pin 20 for ground

Done two boxes now, cheers for all your help guys

Nikko
 
Back
Top