mgcamd?

[h=2]How to use Mgcamd with CCcam and Newcs[/h]

This is some information about how to add C & N lines to mgcamd.
This particular post will refer to its use for the Azbox, but can be adopted to use with other receivers using Enigma and Enigma2.
The location of the files will depend on the image you use. In linux they will be in /var/keys or /usr/keys or something similar.
For the Azbox, all files will be found in the folder /PLUGINS/OpenXCAS/mgcamd which makes things extremely simple and is why I selected that receiver.

There are 3 important files needed for sharing:

mg_cfg
cccamd.list
and
newcamd.list

To allow mgcamd to share from both CCcam and Newcs, you must ensure that in the file mg_cfg, you edit the settings for the value of G: { x }

Settings are cumulative, you sum the values of the emus you want to connect to.. Have a quick look, but don't dwell on it.

Set G: { 33 }

Simple so far? it gets easier..

Edit cccamd.list and paste in a C-line as normal e.g.

C: myfriend.dyndns.com 12000 myname mypass

close and save.

Edit newcamd.list

You may see something like:

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000

leave that alone..

If someone gives you an N-line like this
N: myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14

add it to the end of the newcamd.list like this:

CWS = myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 server1

Close and save

Restart mgcamd.

Click to expand...

gunnertrev said:

hi lads im looking for a little help installing mgcamd 1.38 on open pli image on dm800se,i downloaded the cam via plugins and the went to DCC var/keys and changed G to 33 and the entered my lines.
this is mg_cfg list

# EMM messages
# 00 don't show any EMMs (default)
# 01 show only valid EMMs
# 02 show valid and bad EMMs with complete data display
M: { 01 }

# ECM messages
# 00 don't show anything about ecm
# 01 normal mode, show pids processed, decoded ecm and cw
# 02 verbose mode, show valid and bad ECMs with data
C: { 01 }

# AU
# 00 disable, no emm pids processed
# 01 enable, emm pids always processed for soft-au and shared cards
# 02 auto, emm started only if channel cant be decoded
# 03 process emm pids for network cards update only
A: { 02 }

# key update (sum 01 or 02 with 04)
# 01 update only new keys, default setting
# 02 update all keys (used for valid PMK checking)
# 04 enable TPS au
# + tps SID, which pmt pid contains au pid
U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)
# 00 files in /var/keys
# 01 files in /tmp
T: { 00 }

# network mode, use summ for several clients
# 00 no network (default)
# 01 newcamd netclient
# 02 radegast netclient
# 04 camd3 netclient
# 08 gbox netclient
G: { 33 }

# network retry, use summ for several options
# 00 disable
# 01 retry every new ecm
# 02 try to connect to offline shares every Q: seconds
# 04 try to detect and fast reconnect to lost (and not used atm) server
# + XX messages number and YY seconds to reconnect
# mg will reconnect to server, if no answer to last XX ecm/keepalive or
# if no answer for last ecm or keepalive sent for YY seconds
# set to 0 to disable
N: { 07 } 5 30

# network ecm timeout in seconds
K: { 05 }

# newcamd dead routes connect retry, sec
Q: { 600 }

# network shares priority
# 00 gbox, newcamd, radegast, camd3 (default)
# 01 camd3, radegast, newcamd, gbox
# 02 newcamd, camd3, gbox, radegast
P: { 00 }

# on screen display type
# 00 No OSD (default)
# 01 neutrino
# 02 enigma
# 03 relook
# + user password for http auth
O: { 00 } username password

# on screen display Options, summ of:
# 01 show emu ecm
# 02 show network shares messages
# 04 show decoding failed / fta
# 08 show emm keys update
# + web port to use for osd
S: { 03 } 80

# Log option, summ of:
# 00 off
# 01 network udp log
# 02 log to console
# 04 file, appended ! delete it by yourself, before it eat all your hdd
# + IP udp-port log-file-name
L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds
# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
# for openbox/elanvision users with remote shares make sense to set it higher than default value,
# to not hammer cards while timeshifting or playing crypted recordings.
E: { 15 }

# cache option, summ of:
# 00 Off (default)
# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
# 02 Ecm data cache, remember CW for (E time
# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
H: { 07 }

# reread files, summ of:
# 00 No (default)
# 01 reread config file on channel change (including priority and ignore, but not replace/cache)
# 02 reread SoftCam.Key on channel change
# 04 reread SoftCam.Key if file changed
R: { 00 }

# debug, summ of
# 00 off (default)
# 01 debug ecm
# 02 debug emm
# 04 debug network ecm
# 08 debug network emm
# 16 debug network login
# 32 show mem/cpu stats every 1 min
# 64 add timestamp to log messages
D: { 00 }

# box type
# 00 autodetect, change only if you think wrong type detected.
# 01 dbox2
# 02 dreambox
# 03 triple-dragon
# 04 relook
# 05 openbox
B: { 00 }
this is newcamd list

CWS_KEEPALIVE = 300
CWS_INCOMING_PORT = 21000
CWS = myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 server 1
CWS_MULTIPLE =
myfriend.dyndns.com 15000 myname mypass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 server2

then i restart the cam but nothing clears ,there are two different lines in the newcamd list from different servers ,i put the second one in the multiple line not sure if that was correct,can anyone see what im doing wrong,thanks.

Click to expand...

robcouk1 said:

Hmmm I have issue installing this on a VU+ duo clone box running black hole

I put the IPK file into the temp and install from thr VU+
but it seems to have the cam and I can enter the line details in,,,,but all of the set-up files are missing

do you have to manually install them or have I got a poor ipk file??

Click to expand...