OpenPLi 4.0 sim2 image daily build

gjstroom

VIP Member
VIP Member
Joined
Dec 20, 2015
Messages
126
Reaction score
249
rHYmcWg.png


More text follows.

OpenPLi-4.0-beta-dm800se #ssl84d:

Code:
You don't have permission to view the code content. Log in or register now.
 
Last edited by a moderator:
CCcam is not working well with this release..
Most probably you need to create a cccam.prio. But a better solution is stop using cccam and switch to oscam.
CCcam hasn't been updated for years now...
 
my network card is not working with this img guys - dm800se sim2.10 ssl84D ..
there's no link green tick, however, IP is obtained form DHCP. But cannot telnet or ftp to box, can ping it ... any advice ?

PS: my friend tried to update like 2yrs old img to this one via software update, box did not boot up, I tried to reflash it with newest openpli, but as mentioned above, network not working :/ any advice here will be much appreciated ... as I already killed few days with troubleshooting of this ... right now box is working with img from 2015/05/02 ...
 
If you can ping it then its not a network issue I wouldnt think, what error are you getting when trying to FTP or Telnet?
 
telnet - press any key to exit, ftp-500 OOPS: priv_sock_get_cmd ...


Sent from my iPhone using Tapatalk
 
my network card is not working with this img guys - dm800se sim2.10 ssl84D ..
there's no link green tick, however, IP is obtained form DHCP. But cannot telnet or ftp to box, can ping it ... any advice ?

PS: my friend tried to update like 2yrs old img to this one via software update, box did not boot up, I tried to reflash it with newest openpli, but as mentioned above, network not working :/ any advice here will be much appreciated ... as I already killed few days with troubleshooting of this ... right now box is working with img from 2015/05/02 ...

Updating a 2 year old image is not a wise thing. Better install a new image.
Not working network seems like a hardware problem, check your power supply.
Also updating the pli4 images in general is asking for trouble. The PLi guys fiddled with the module version numbers, so own builds (like my build) get to update lots of parts, since the dreamboxes are already low on available flash, it almost fails in every case...
I don't test the images that often, it is possible some build dates do not work. It's an automated build process which uses the OpenPLi git source.
 
Updating a 2 year old image is not a wise thing. Better install a new image.
Not working network seems like a hardware problem, check your power supply.
Also updating the pli4 images in general is asking for trouble. The PLi guys fiddled with the module version numbers, so own builds (like my build) get to update lots of parts, since the dreamboxes are already low on available flash, it almost fails in every case...
I don't test the images that often, it is possible some build dates do not work. It's an automated build process which uses the OpenPLi git source.

Hi gjstroom,

I know that updating old image is not a good thing but he did it without my knowledge.
No issue at all, I've downloaded your latest img, everything went cool but the network card :/ your old image (from 2015/02) is working very well, so do you still think there's any HW issue ?

Thanks.
 
Hi gjstroom,
I know that updating old image is not a good thing but he did it without my knowledge.
No issue at all, I've downloaded your latest img, everything went cool but the network card :/ your old image (from 2015/02) is working very well, so do you still think there's any HW issue ?
Thanks.
I just flashed todays image and it's working fine. I promise you, nothing has been changed from my site. It could have been a **** up in the PLi git source, but I seriously doubt it. I have seen a lot of image building problems, I have never encountered non working wired network.
By the way the green nic light turns on immediately when you power on the box.
Do you perhaps restore old configurations ? Is your dhcp working properly ? Maybe the box gets another ip then you used to use ?
 
Last edited:
I just flashed todays image and it's working fine. I promise you, nothing has been changed from my site. It could have been a **** up in the PLi git source, but I seriously doubt it. I have seen a lot of image building problems, I have never encountered non working wired network.
By the way the green nic light turns on immediately when you power on the box.
Do you perhaps restore old configurations ? Is your dhcp working properly ? Maybe the box gets another ip then you used to use ?

Hi gjstroom,

well I was surprised as well - my other devices work on same router well, so that's why I asked about the image. I have DM800HD SE SIM 2.10 with latest(?) SSL84D.
My other DM800HD SE v2 with SIM2.2 SSL88A works with your images & on same router as well.
I had to return the DM800HD SE SIM2.10 to my friend as he wanted to watch TV - currently as I mentioned, there's your image from February 2015. Power source is OK, 12,3V, and cable network card and usb wifi is working with your img from 2015.
Green light is there when I power the box, also I get an internal IP, I am also able to log in to webif, but no telnet or FTP access is working. And also I cannot update it via menu in box, green tick in LINK - in Network menu in box - is not there. So that is really strange. That's why I asked ... and I don't know many people with this same box as my friend has, that's why I asked ...
 
no issue with image at all sound here
 
Hi gjstroom,

well I was surprised as well - my other devices work on same router well, so that's why I asked about the image. I have DM800HD SE SIM 2.10 with latest(?) SSL84D.
My other DM800HD SE v2 with SIM2.2 SSL88A works with your images & on same router as well.
I had to return the DM800HD SE SIM2.10 to my friend as he wanted to watch TV - currently as I mentioned, there's your image from February 2015. Power source is OK, 12,3V, and cable network card and usb wifi is working with your img from 2015.
Green light is there when I power the box, also I get an internal IP, I am also able to log in to webif, but no telnet or FTP access is working. And also I cannot update it via menu in box, green tick in LINK - in Network menu in box - is not there. So that is really strange. That's why I asked ... and I don't know many people with this same box as my friend has, that's why I asked ...
Do I understand correctly you had 2 DM800HD SE SIM2.10 in the same network ? If so, that's quite possible the problem as the boxes do have the same mac-address. In that case your router can't make out which box is which.
 
hi, nope, I said I had 1 DM800HD SE v1 SIM2.10 SSL84D and 1 DM800HD SE v2 SIM2.2 SSL88A ... no chance they had same MAC address, even USB wifi did not work - it has IP assigned but ... the rest u know ...


Sent from my iPhone using Tapatalk
 
as said earlier no issue with network image works fine
 
as said earlier no issue with network image works fine
I also think my image is not the problem, all working fine here on dm800se and dm800se sr4.
I don't understand Phoenix's problem.
 
no idea mate deffo not image related
have it running on 3 boxes here setting up for others
 
Last edited:
Running here on two dm800se perfectly,

Did you double check Mac addresses?

Sent from my Z using Tapatalk
 
what dreamboxes do u have? which sim? which ssl? mac is out of scope as img from 2015 is working great ... on same router with dhcp etc...


Sent from my iPhone using Tapatalk
 
dm 800se sim2 bootloader 84 as the image is meant for with no issues
 
Back
Top