VU+ Solo² Full HD Twin DVB-S2 Linux HDTV PVR
Digital satellite receiver for digital TV and radio programs.
The main feature of the 1300-MHz processor the VU + Solo ². Experience high definition TV with your VU + Solo ².
• Transcoding feature
• Airplay function
• Opera browser
• HbbTV
• HDMI 1.4 connection
• HD PIP
• Gigabit Lan
• Plug and Play support for 2.5 "SATA - Hard Drives
• 12 character VFD display
• External 12 V power supply
Technical highlights:
o 1300 MHz MIPS processor
o 256MB Flash
o 1GB DDR3 DRAM
o Gigabit Lan
o 1 x DVB Common Interface slot
o 2 x smartcard reader (Xcrypt)
o 3 x USB (1x front, 2x rear)
o SPDIF optical audio output (digital)
o 1 x HDMI 1.4 video / audio output (digital)
o 1 x Scart (TV)
o 1 x RCA video output
o 2 x audio (analog) output (L / R) RCA
o Plug and Play support for 2.5 "SATA - Hard Drives
o unlimited channel lists for TV / Radio
o EPG (electronic program guide) support
o Support of Bouquet lists
o OSD in many languages and skin-support
o auto / manual channel search
o DiSEqC 1.0/1.1/1.2, USALS
o External 12 volt power supply
o Power switch
VU + Solo ² Specifications:
DVB-S2 tuner:
Input frequency range 950 .. 2150 MHz
Signal Level - 65 dBm ... - 25 dBm
Tuner Input Connector F-Type female
Input impedance 75 ohms
AFC + / - 3.5 MHz
QPSK and 8PSK demodulation
FEC Viterbi and Reed-Solomon
Viterbirate 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9
Roll-off Factor 35%
Common Interface:
Common-Interface Power Consumption max. 0.35 A/5V
Video decoder:
Video Compression MPEG-2 / H.264 and MPEG-1 compatible
Video Standard PAL G / 25 Hz, NTSC
4:3 / 16:9
Letterbox for 4:3 TV-Device
Digital output:
Output Level 0,5 Vss on 75 Ohm
Frequency: 32 kHz, 44.1 kHz, 48 kHz
S / PDIF optical, coaxial (AC3)
Audio decoder:
Audio compression MPEG-1 & MPEG-2 Layer I and II, MP3
Audio Mode Dual (main / sub), Stereo
Frequency: 32 kHz, 44.1 kHz, 48 kHz, 16 kHz, 22.05 kHz, 24 kHz
Output analog:
Output Level L / R 0,5 Vss on 600 Ohm
THD> 60 dB (1 kHz)
Crosstalk <-65 dB
Video parameter:
Input Level FBAS 1 Vss + / - 0.25 dB on 75 Ohm
TV-Scart:
Output: FBAS, RGB, over OSD
Ethernet:
1000/100/10 MBit compatible interface
USB:
USB 2.0 (3x)
LNB power and DVB-S2 Tuner:
LNB Current 400mA max. , Short-circuit proof
LNB Voltage horizontal "no load 19.5 V" 17.6 V at 400mA
LNB Voltage vertical "no load 14.5 V" 11,8 V at 400mA
LNB is switched off in the standby mode,
Control the satellite position:
DiSEqC 1.0/1.1/1.2 and USALS - Rotor Control
Power consumption:
<13W (in operation, with LNB)
<12W (in operation, without LNB)
<0.5 W (Deep-Standby-Mode)
Input voltage:
External power supply:
Input:
110-240V AC / 50-60Hz / 1,0 A
Output:
12V = / 3,5 A
General:
Ambient Temperature +15 ° C. .. +35 ° C
Humidity <80%
Dimensions (W x D x H): 280 mm x 200 mm x 50
Weight: 2.0 kg without HDD
Q: VTi-Board
Digital satellite receiver for digital TV and radio programs.
The main feature of the 1300-MHz processor the VU + Solo ². Experience high definition TV with your VU + Solo ².
• Transcoding feature
• Airplay function
• Opera browser
• HbbTV
• HDMI 1.4 connection
• HD PIP
• Gigabit Lan
• Plug and Play support for 2.5 "SATA - Hard Drives
• 12 character VFD display
• External 12 V power supply
Technical highlights:
o 1300 MHz MIPS processor
o 256MB Flash
o 1GB DDR3 DRAM
o Gigabit Lan
o 1 x DVB Common Interface slot
o 2 x smartcard reader (Xcrypt)
o 3 x USB (1x front, 2x rear)
o SPDIF optical audio output (digital)
o 1 x HDMI 1.4 video / audio output (digital)
o 1 x Scart (TV)
o 1 x RCA video output
o 2 x audio (analog) output (L / R) RCA
o Plug and Play support for 2.5 "SATA - Hard Drives
o unlimited channel lists for TV / Radio
o EPG (electronic program guide) support
o Support of Bouquet lists
o OSD in many languages and skin-support
o auto / manual channel search
o DiSEqC 1.0/1.1/1.2, USALS
o External 12 volt power supply
o Power switch
VU + Solo ² Specifications:
DVB-S2 tuner:
Input frequency range 950 .. 2150 MHz
Signal Level - 65 dBm ... - 25 dBm
Tuner Input Connector F-Type female
Input impedance 75 ohms
AFC + / - 3.5 MHz
QPSK and 8PSK demodulation
FEC Viterbi and Reed-Solomon
Viterbirate 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9
Roll-off Factor 35%
Common Interface:
Common-Interface Power Consumption max. 0.35 A/5V
Video decoder:
Video Compression MPEG-2 / H.264 and MPEG-1 compatible
Video Standard PAL G / 25 Hz, NTSC
4:3 / 16:9
Letterbox for 4:3 TV-Device
Digital output:
Output Level 0,5 Vss on 75 Ohm
Frequency: 32 kHz, 44.1 kHz, 48 kHz
S / PDIF optical, coaxial (AC3)
Audio decoder:
Audio compression MPEG-1 & MPEG-2 Layer I and II, MP3
Audio Mode Dual (main / sub), Stereo
Frequency: 32 kHz, 44.1 kHz, 48 kHz, 16 kHz, 22.05 kHz, 24 kHz
Output analog:
Output Level L / R 0,5 Vss on 600 Ohm
THD> 60 dB (1 kHz)
Crosstalk <-65 dB
Video parameter:
Input Level FBAS 1 Vss + / - 0.25 dB on 75 Ohm
TV-Scart:
Output: FBAS, RGB, over OSD
Ethernet:
1000/100/10 MBit compatible interface
USB:
USB 2.0 (3x)
LNB power and DVB-S2 Tuner:
LNB Current 400mA max. , Short-circuit proof
LNB Voltage horizontal "no load 19.5 V" 17.6 V at 400mA
LNB Voltage vertical "no load 14.5 V" 11,8 V at 400mA
LNB is switched off in the standby mode,
Control the satellite position:
DiSEqC 1.0/1.1/1.2 and USALS - Rotor Control
Power consumption:
<13W (in operation, with LNB)
<12W (in operation, without LNB)
<0.5 W (Deep-Standby-Mode)
Input voltage:
External power supply:
Input:
110-240V AC / 50-60Hz / 1,0 A
Output:
12V = / 3,5 A
General:
Ambient Temperature +15 ° C. .. +35 ° C
Humidity <80%
Dimensions (W x D x H): 280 mm x 200 mm x 50
Weight: 2.0 kg without HDD
Q: VTi-Board
Last edited:
