Error codes

abodgbr

Inactive User
Joined
Nov 30, 2005
Messages
4
Reaction score
0
I got a 4001N of my m8 when I switch it on three green lights flash on the front
it then goes loopy with all the counting down quickly and then LA IT and ERR5 pops up then it starts all over again. Any body any idea whats wrong with thedamn thing or am I just unlucky and got a schitzo box???
 
I got a 4001N of my m8 when I switch it on three green lights flash on the front
it then goes loopy with all the counting down quickly and then LA IT and ERR5 pops up then it starts all over again. Any body any idea whats wrong with thedamn thing or am I just unlucky and got a schitzo box???

LAIT is a sign your box is attempting a firmware upgrade. Err5, I think, means it has failed !
 
It could be ERA5 which along with lait is part of the upgrade process, let it run through and hopefully it should be completed in 5 minutes or so.
 
I got a 4001N of my m8 when I switch it on three green lights flash on the front
it then goes loopy with all the counting down quickly and then LA IT and ERR5 pops up then it starts all over again. Any body any idea whats wrong with thedamn thing or am I just unlucky and got a schitzo box???

I tdoes that mate when the numbers count down/up and flashes that....leave it for 5 minutes and it should have new firmware updated...as nozzer stated :)
 
Cheers guys this is exactly what happens when I put power cable in
Pace, tune, nlt, PAt, numbers count up, Pd Ld, LA lt, EAA5 then it starts all over again. Ilet it run but still no joy.
 
It could be ERA5 .....

Well spotted - I forgot about the ERAS bit !

Cheers guys this is exactly what happens when I put power cable in
Pace, tune, nlt, PAt, numbers count up, Pd Ld, LA lt, EAA5 then it starts all over again. Ilet it run but still no joy

If the box continues to attempt updates then its in an update loop. This can happen when when the original update fails, possibly due to some form of hardware failure or maybe an anti-update modification.

You could try and reset the box (pull the jumper). As its a 4001N I presume its in a true NTL area so it should set its NetId again automatically. Make a note of the parameters first though just in case you have to do a manual entry.
 
On This Subject I Have A 1000 Box That Wont Update. Comes Up With Error 4 And Error 2. I No One Is Due To The Fact I Can't Get In The Eng Menu To Correct The Netid Hence It Wont Update. But Whats The Other. I've Lost My List Of Error Codes.
 
here you go mate
Err1_ CRC fail across Primary Loader image
Err2_ Simm error
Err3_ Insufficient NVRAM
Err4_ Flash Fail or can't find platform object
Err5_ NVRAM not found

Tuning Sequence Related Errors

Er10_ Unable to Tune to Last frequency
Er11_ Unable to Tune to Home Frequency
Er12_ Unable to Tune to any of the last NIT defined frequencies
Er13_ Unable to scan for a frequency
Er14_ Unable to scan for a symbol rate
Er16_ Unable to tune to hardcoded frequency

Input Stream Errors

Er20_ Timeout on receiving NIT
Er21_ Timeout on receiving PAT
Er22_ Timeout on receiving PMT
Er23_ Timeout on receiving object data
Er24_ Timeout on receiving TDT
Er25_ Sync loss has occurred on the input stream

Object Validation

Er30_ Object CRC Fail
Er31_ Object Digital Signature Fail

Flash programming errors

Er40_ Insufficient Flash ( NAND Flash Specific )
ErrC_ Failed to Erase Flash Sector
ErrD_ Failed to Program a Flash sector.
ErrE_ CRC Failure of image just programmed into Flash

Err 1001 not enough credit for ppv
Err 1002 pin locked
Err1003 viewing card problem
Err1004 viewing card problem
Err1005 no card found
Err1006 blacklisted card
Err1007 card suspeneded
Err1008/9 card not paired
Err1010/11 viewing card rights problem
 
Back
Top