Page 1 of 4 123 ... Last
  1. #1
    irlam's Avatar
    Join Date
    May 2005
    Location
    Bolton UK
    Posts
    825
    DW Cash
    227
    Post Thanks / Like
    Downloads
    6
    Uploads
    2
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Question Help Please With Dm800 Boot Problem

    My DM800 freezes as shown in the picture,ive tried every boot loader from ss53-ss72

    The box has previously been working but just stoped booting and started freezing upon boot.




    ive used the following images to name but a few.

    Nabilo_BlackHole_DM800_RC1.nfi
    gemini2-440-dm800_ss69 modified by jams01.nfi
    nabilov6bootloader67.nfi
    pli-enigma2-jade3-dm800-20090719-6555_8a8f8.nfi
    NabiloBlackHole-11-BL72-DM800


    I am using dreamup 1.3.3.2 to flash the DM800
    even with the recover bad sectors option on in dreamup

    I get no error like "no ca found"

    I have tried looking for the fault using hypterm (the boot log is below)


    (c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
    Dreambox DM800
    FIRST STAGE 1.00 {BO23456}
    2ND STAGE OK, build #67 (20081024)

    0.000 - BCM board setup
    0.022 - fp init
    0.023 - ca init
    0.399 - load config
    dCA: not existent, loading defaults
    0.430 - config loaded.
    * press [S] to enter setup
    OLED found!
    BOOT #67(20081024)
    detected jffs2 blocksize: 16kb
    ++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++
    ++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++
    ++++++++++++++++++++++++++++++++++++++++++++++++++ +++++++++++++
    ++++++++++++++++++++++++++++++++++++++++++++++++++ +
    dreamupd initialized
    Scanning JFFS2 FS: . done.
    /flash/bootlogo.elf
    bootlogo size: 106538
    using 1280x720p (60.00 Hz)
    Using the Small jpeg decoder library, Copyright (c) 2006, Luc Saillard <luc@saillard.org>
    parsing JPEG header..
    JPEG Size: 1280x720
    /flash/vmlinux.gz
    Done initializing U0
    found console= 0
    HI WORLD!!!
    gathering mode: 0x00000264 at 0x0xb000040c
    split mode: 0x00000001 at 0xb0000410
    board_init_once: regval=44ac6502, ddr_strap=3, 4 chips, pci_size=2
    Detected 256 MB on board
    cfeBootParms ===>
    Number of Nand Chips = 0
    Default command line =
    root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
    1 831ffee0 8303ab98
    Kernel boot options: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
    Initial CP0 22 value : 0x00010020
    Updated CP0 22 value : 0x00000020
    CP0 reg 22 sel 0 to 5: 0xe3800000 0x00000020 0x00000000 0x00000020 0x00000000 0x00000020
    Sundry 0xb0404000, chipId 0x00007401, bcm7401Cx 0x21
    CPU revision is: 00020000
    Determined physical RAM map:
    memory: 10000000 @ 00000000 (usable)
    User-defined physical RAM map:
    node [00000000, 08000000: RAM]
    node [08000000, 08000000: RSVD]
    <4>bootmem_init: map 0 type 1
    <4>bootmem_init: curr_pfn 0x0000039f last_pfn 0x0000ffff max_low_pfn 0x00010000
    <4>bootmem_init: Done
    <7>On node 0 totalpages: 65536
    <7> DMA zone: 65536 pages, LIFO batch:31
    <7> Normal zone: 0 pages, LIFO batch:1
    <7> HighMem zone: 0 pages, LIFO batch:1
    Before resource_init
    After resource_init
    Built 1 zonelists
    <5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw mem=128M console=null
    before init RAC 0x02a00000 0x00000000
    after init RAC 0x02a0000f 0x0fff0000
    Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
    Primary data cache 32kB, 2-way, linesize 16 bytes.
    MIPS_CACHE_ALIASES = ON
    end of ld_mmu_r4xx0
    end of local_tlb_init
    Wired: 17
    Index: 0 pgmask=16Mb va=d0000000 asid=00
    [pa=d0000000 c=2 d=1 v=1 g=1]
    [pa=d1000000 c=2 d=1 v=1 g=1]

    Index: 1 pgmask=16Mb va=d2000000 asid=00
    [pa=d2000000 c=2 d=1 v=1 g=1]
    [pa=d3000000 c=2 d=1 v=1 g=1]

    Index: 2 pgmask=16Mb va=d4000000 asid=00
    [pa=d4000000 c=2 d=1 v=1 g=1]
    [pa=d5000000 c=2 d=1 v=1 g=1]

    Index: 3 pgmask=16Mb va=d6000000 asid=00
    [pa=d6000000 c=2 d=1 v=1 g=1]
    [pa=d7000000 c=2 d=1 v=1 g=1]

    Index: 4 pgmask=16Mb va=d8000000 asid=00
    [pa=d8000000 c=2 d=1 v=1 g=1]
    [pa=d9000000 c=2 d=1 v=1 g=1]

    Index: 5 pgmask=16Mb va=da000000 asid=00
    [pa=da000000 c=2 d=1 v=1 g=1]
    [pa=db000000 c=2 d=1 v=1 g=1]

    Index: 6 pgmask=16Mb va=dc000000 asid=00
    [pa=dc000000 c=2 d=1 v=1 g=1]
    [pa=dd000000 c=2 d=1 v=1 g=1]

    Index: 7 pgmask=16Mb va=de000000 asid=00
    [pa=de000000 c=2 d=1 v=1 g=1]
    [pa=df000000 c=2 d=1 v=1 g=1]

    Index: 8 pgmask=16Mb va=e0000000 asid=00
    [pa=e0000000 c=2 d=1 v=1 g=1]
    [pa=e1000000 c=2 d=1 v=1 g=1]

    Index: 9 pgmask=16Mb va=e2000000 asid=00
    [pa=e2000000 c=2 d=1 v=1 g=1]
    [pa=e3000000 c=2 d=1 v=1 g=1]

    Index: 10 pgmask=16Mb va=e4000000 asid=00
    [pa=e4000000 c=2 d=1 v=1 g=1]
    [pa=e5000000 c=2 d=1 v=1 g=1]

    Index: 11 pgmask=16Mb va=e6000000 asid=00
    [pa=e6000000 c=2 d=1 v=1 g=1]
    [pa=e7000000 c=2 d=1 v=1 g=1]

    Index: 12 pgmask=16Mb va=e8000000 asid=00
    [pa=e8000000 c=2 d=1 v=1 g=1]
    [pa=e9000000 c=2 d=1 v=1 g=1]

    Index: 13 pgmask=16Mb va=ea000000 asid=00
    [pa=ea000000 c=2 d=1 v=1 g=1]
    [pa=eb000000 c=2 d=1 v=1 g=1]

    Index: 14 pgmask=16Mb va=ec000000 asid=00
    [pa=ec000000 c=2 d=1 v=1 g=1]
    [pa=ed000000 c=2 d=1 v=1 g=1]

    Index: 15 pgmask=16Mb va=ee000000 asid=00
    [pa=ee000000 c=2 d=1 v=1 g=1]
    [pa=ef000000 c=2 d=1 v=1 g=1]

    Index: 16 pgmask=16Mb va=f0000000 asid=00
    [pa=f0000000 c=2 d=1 v=1 g=1]
    [pa=f1000000 c=2 d=1 v=1 g=1]

    $$$$$$$$$$ 1394 dev id ffffffff
    $$$$$$$$$$ mini slot dev id ffffffff
    $$$$$$$$$$ external dev id ffffffff
    $$$$$$$$$$SATA dev id 02421166
    Synthesized TLB refill handler (20 instructions).
    Synthesized TLB load handler fastpath (32 instructions).
    Synthesized TLB store handler fastpath (32 instructions).
    Synthesized TLB modify handler fastpath (31 instructions).
    timer irq 68 end 57
    PID hash table entries: 2048 (order: 11, 32768 bytes)
    mips_counter_frequency = 148000000 from Calibration, = 148500000 from header(CPU_MHz/2)
    Using 148.501 MHz high precision timer.
    Console: colour dummy device 80x25
    ################## brcm_serial_console_init, sercon=80325f50

    Has anybody had this problem before and managed to fix it?

    or any sugestions on how to fix it?

    the box has a sim that enables boot loader 72 in it,

    so i dont think its a boot loader problem as i dont get the "no ca found" error


    Report this post


    «¤IRL@M¤»

  2. #2

    Join Date
    Sep 2009
    Posts
    226
    DW Cash
    25
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    Freezes in which picture?

  3. #3

    Join Date
    Sep 2007
    Posts
    352
    DW Cash
    25
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    try disconectiong the dvi cable.....

    boot the box....

    if it boots, reconect the dvi cable.......

  4. #4
    irlam's Avatar
    Join Date
    May 2005
    Location
    Bolton UK
    Posts
    825
    DW Cash
    227
    Post Thanks / Like
    Downloads
    6
    Uploads
    2
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    The box is not conected to anything only power during the boot process
    «¤IRL@M¤»

  5. #5

    Join Date
    Sep 2009
    Posts
    226
    DW Cash
    25
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    Have you tried restarting multiple times? Mine has froze a few times but a quick reboot fixes it?

    I assume you have tried a complete re-flash using DreamUp?

  6. #6
    thfccambs's Avatar
    Join Date
    Aug 2007
    Posts
    208
    DW Cash
    25
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    Quote Originally Posted by irlam View Post
    The box is not conected to anything only power during the boot process
    Why? So it's not got any signal or anything?
    jUST POWER CABLE?
    Have you tried it with lnb all connected?

    Id also try re flash, do mine using web interface.

    Is it an original or clone?

  7. #7

    Join Date
    Jan 2006
    Posts
    329
    DW Cash
    25
    Post Thanks / Like
    Downloads
    1
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    had mine freezing on boot thismorning just reflashed using the http method
    power of box / take out pwr lead / plug the lead back in and hold the power button on the front untill dhcp and your ip comes up / goto your pc and type in
    http://192.168.1.and yours in here you will have a web page come up and click on the flash button / select the nfi file u want to flash and click on flash/upgrade
    wait till its 100% and then turn off/on your box and it should boot with the image you have chossen
    then set it up how you like it , hope this helps

    i flash mine through a router and gigabit switch with no problems

  8. #8
    bro's Avatar
    Join Date
    Mar 2005
    Location
    Gods Country
    Posts
    9,448
    DW Cash
    25
    Post Thanks / Like
    Downloads
    1
    Uploads
    0
    Mentioned
    7 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    u having any luck with your irlam,having same probs now with nanis
    Last edited by bro; 25th September 2009 at 22:28.


  9. #9
    irlam's Avatar
    Join Date
    May 2005
    Location
    Bolton UK
    Posts
    825
    DW Cash
    227
    Post Thanks / Like
    Downloads
    6
    Uploads
    2
    Mentioned
    10 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    Well,what can i say apart from EXCELENT,got sent a replacement box and all back up and running again THANKYOU LINUXSAT!!!!!!!



    Welcome to Linuxsat
    «¤IRL@M¤»

  10. #10

    Join Date
    Oct 2009
    Posts
    15
    DW Cash
    25
    Post Thanks / Like
    Downloads
    0
    Uploads
    0
    Mentioned
    0 Post(s)
    Tagged
    0 Thread(s)

    Re: Help Please With Dm800 Boot Problem

    I'm having a similar problem with a Dm800 HD Clone.

    It was working fine aside from a few minor issues, so I flashed with NabiloBlackHole-11-BL72-**********************.nfi & updated the bootloader to SecondStage-72-R1-DM800-**********************.nfi

    I then went into updates and it downloaded about 30 updates and I restarted the box.

    I got the following error on boot: ERR01: NO CA FOUND

    I can reload the SecondStage-72-R1-DM800-**********************.nfi
    file through Dreamup, but this error 'System message - hardware could not be verified - contact Dreambox support '

    I can't load the box in standby by holding in the power button so can't access the web interface.

    It won't recognise NabiloBlackHole-11-BL72-**********************.nfi through Dreamup so I can't reflash.

    Has anyone else experienced this and how did you rectify?

    Thanks



Page 1 of 4 123 ... Last

Similar Threads

  1. dm800 wont boot,
    By dilly1066 in forum Dreambox DM800HD Support
    Replies: 35
    Last Post: 2nd March 2013, 03:03
  2. dm800 boot problem
    By jdunlo in forum Dreambox Receiver Discussion
    Replies: 5
    Last Post: 16th December 2010, 13:01
  3. Dm800 wont boot up
    By alonso in forum Dreambox DM800HD Support
    Replies: 10
    Last Post: 31st October 2010, 09:06
  4. HELP - DM800 won't boot/can get in linux ?
    By bilabonic in forum Dreambox Receiver Discussion
    Replies: 2
    Last Post: 16th September 2010, 16:00
  5. dm800 boot up channel
    By nivag in forum Dreambox Receiver Discussion
    Replies: 6
    Last Post: 25th April 2010, 12:25

User Tag List

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Log in

Log in